Herunterladen Inhalt Inhalt Diese Seite drucken

Honeywell HZ-510E Gebrauchsanweisung Seite 7

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 9
ENGLISH
9. Lever for height adjustment
10. Feet
11. Power lamp
12. Safeguard System marker
FIRST TIME OF USE
1. Before starting to use the heater, read through all the
instructions.
2. Unpack the heater and the power cord. Remove all the
packaging materials and dispose of them for recycling.
INSTRUCTIONS FOR USE
1. Place the heater only on a firm, even surface where the
heater cannot fall over, fall down or be knocked over.
2. Make sure that the heater is switched off and that the
thermostat switch is in the lowest position (3). Insert the
power plug into the socket. Do not touch the power cord
with wet hands.
3. Make sure that the air intake vent (5) and outlet vent (6)
are not covered up and that no objects have got inside.
The air intake and outlet vents must always be free.
4. The height of the front foot is adjustable. Turn the lever
for height adjustment (9) anti-clockwise to increase the
height. Turn the lever clockwise to lower the height.
5. Turn the power switch (1) to the position of the desired
heat setting:
~~1100 Watts
~~~1800 Watts
6. Turn the thermostat switch (2) clockwise to the highest
position (4). The power lamp lights up.
7. When the desired room temperature has been reached,
turn the thermostat switch (2) anti-clockwise until you
hear it „click". Now the heater is switched off.
8. Now turn the thermostat switch (2) back clockwise a
bit. The heater will now automatically switch on and off to
maintain the desired room temperature.
9. The further clockwise you turn the thermostat switch,
the higher the room temperature will be.
10. Before handling, moving or cleaning the heater, switch
it off at the power switch (1) and turn the thermostat
switch (2) to the lowest position (3). Pull the power plug
out of the socket and allow the heater to cool for at least
20 minutes. Always use the transport handle when moving
the heater (8).
Safeguard™ System
This heater is equipped with a Safeguard™ System (12)
which is located at the front on the air outlet vent (6).
When the appliance is heating, the Safeguard marker
changes colour from black to red. This signalizes that the
heater is hot and must not be touched until it has been
switched off and the marker has turned completely black
again.
Overheating shut-off for the heater
1. The heater is equipped with overheating shut-off which
switches the heater off automatically when the temperatu-
re inside the appliance exceeds the normal running tempe-
rature. This protective device applies only to the appliance
and has no influence on room temperature regulation.
2. The appliance will not function if the overheating shut-
off is activated.
3. Turn the power switch to O and the thermostat switch
(2) to the lowest position (3). Pull the power plug out of
the socket.
4. Now allow the heater to cool at least until the Safeguard
marker is completely black.
5. Remove any objects from inside or in front of the air
intake (5) or outlet (6) vents, or use a vacuum cleaner to
clean the openings which caused the faulty running or
overheating. If heavy dust deposits are also visible inside
the heater, please get the appliance cleaned at a service
centre.
6. Resume using the heater as described under „User
instructions".
Further safety features
1. The heater has a back-up safety fuse.
2. This heater has a motor cut-out which switches the
motor off if it is operating at an above normal temperature.
CLEANING, MAINTENANCE, DISPOSAL
We recommend you to clean the heater regularly. Follow
the instructions for cleaning and maintenance, so as not to
impair the functioning of the heater.
Cleaning
1. Before you start with the cleaning, turn the thermostat
switch (2) to the lowest position (3) and pull the power
plug out of the socket. Allow the heater to cool at least
until the Safeguard marker is completely black again.
2. Clean the air intake (5) and outlet (6) vents with a vacu-
um cleaner to remove dust from the motor and heating
element.
3. Clean the outside of the heater with a soft, dry cloth. Do
not use water, wax, polish, or other chemical cleaners.
6

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis