Operation - Makita 6319D Bedienungsanleitung

Speed change
Fig.4
This tool has a three-gear speed change lever. To change
the speed, first switch off the tool and then slide the speed
change lever to the "1" position for low speed, "2" position
for medium speed or "3" position for high speed. Be sure
that the speed change lever is set to the correct position
before operation. Use the right speed for your job.
NOTE:
When changing the position from "1" to "3" or from
•
"3" to "1", it may be a little difficult to slide the
speed change lever. At this time, switch on and run
the tool for a second at the "2" position, then stop
the tool and slide to your desired position.
CAUTION:
Always set the speed change lever fully to the
•
correct position. If you operate the tool with the
speed change lever positioned halfway between
the "1" position, "2" position and "3" position, the
tool may be damaged.
Do not use the speed change lever while the tool is
•
running. The tool may be damaged.
Selecting action mode
Fig.5
This tool has an action mode change lever. For drilling,
slide the action mode change lever to the left (
For screwing, slide the action mode change lever to the
right ( symbol).
NOTE:
When changing the position from "
•
may be a little difficult to slide the mode change
lever. At this time, switch on and run the tool for a
second at the "
slide to your desired position.
CAUTION:
Always slide the action mode change lever all the
•
way to your desired mode position. If you operate
the tool with the lever positioned halfway between
the mode symbols, the tool may be damaged.
Do not use the action mode change lever while the
•
tool is running. The tool may be damaged.
Adjusting the fastening torque
Fig.6
The fastening torque can be adjusted in 16 steps by
turning the adjusting ring so that its graduations are
aligned with the pointer on the tool body.
First, slide the action mode change lever to the position
of symbol.
The fastening torque is minimum when the number 1 is
aligned with the pointer, and maximum when the
marking is aligned with the pointer. The clutch will slip at
various torque levels when set at the number 1 to 16.
Before actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
" to "
" position, then stop the tool and
which torque level is required for a particular application.
NOTE:
The adjusting ring does not lock when the pointer
•
is
graduations.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before carrying out
any work on the tool.
Installing side grip (auxiliary handle)
Fig.7
Always use the side grip to ensure operating safety.
Insert the side grip so that the protrusions on the grip
base fit in between the grooves on the tool barrel. Then
tighten the grip by turning clockwise.
Installing or removing driver bit or drill bit
Fig.8
Turn the sleeve counterclockwise to open the chuck
jaws. Place the bit in the chuck as far as it will go. Turn
the sleeve clockwise to tighten the chuck. To remove the
bit, turn the sleeve counterclockwise.
When not using the driver bit, keep it in the bit holders.
symbol).
Bits 45 mm long can be kept there.
Fig.9
Adjustable depth rod (Optional accessory)
Fig.10
", it
The adjustable depth rod is used to drill holes of uniform
depth. Loosen the thumb screw, set to desired position,
then tighten the thumb screw.

OPERATION

Screwdriving operation
Fig.11
First, slide the action mode change lever to the position
of symbol and select the fastening torque.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
NOTE:
Make sure that the driver bit is inserted straight in
•
the screw head, or the screw and/or bit may be
damaged.
When driving wood screws, predrill pilot holes to
•
make driving easier and to prevent splitting of the
workpiece. See the chart.
6
positioned only halfway between the