Product Description And Specifications; Noise/Vibration Information - Bosch GSH 3 E Professional Originalbetriebsanleitung

OBJ_BUCH-715-004.book Page 11 Monday, August 22, 2016 12:47 PM
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The power tool is designed for chiselling in concrete, brick,
stones and asphalt as well as, equipped with the correspond-
ing accessories, for taking off tiles, plaster, rests of glue and
stucco.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Dust protection cap
2 Locking sleeve
3 Chisel adjustment ring (Vario-Lock)
4 Lock-on button for On/Off switch
5 On/Off switch
6 Auxiliary handle (insulated gripping surface)
7 Handle (insulated gripping surface)
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Demolition Hammer
Article number
Rated power input
Impact rate
Impact energy per stroke
according to
EPTA-Procedure 05/2009
Chisel positions
Chiselling capacity in
concrete of medium hardness
Tool holder
Lubrication
Weight according to
EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Bosch Power Tools

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-6.
Typically the A-weighted noise levels of the product are:
Sound pressure level 90 dB(A); sound power level
101 dB(A). Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 60745-2-6:
Chiselling: a
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
 Before any work on the machine itself, pull the mains
Auxiliary Handle
 Operate your machine only with the auxiliary handle 6.
GSH 3 E
The auxiliary handle 6 can be set to any position for a secure
0 611 320 7..
and low-fatigue working posture.
W 650
– Turn the bottom part of the auxiliary handle 6 in counter-
-1
min 0– 3500
J 2.6
Changing the Tool
12
With the SDS-plus tool holder, simple and convenient tool
kg/h 31
changing is possible without additional aids.
SDS-plus The dust protection cap 1 largely prevents the entry of drilling
dust into the tool holder during operation. When inserting the
Oil lubrication
tool, take care that the dust protection cap 1 is not damaged.
 A damaged dust protection cap should be changed im-
kg 3.5
/II
(triax vector sum) and uncertainty K
h
2
=17.5 m/s , K=1.5 m/s
h
plug.
clockwise direction and swivel the auxiliary handle 6 to the
desired position. Then retighten the bottom part of the
auxiliary handle 6 by turning in clockwise direction.
mediately. We recommend having this carried out by
an after-sales service.
English | 11
2
1 609 92A 2BH | (22.8.16)