Thomashilfen RECARO Monza Reha Montage- Und Gebrauchsanleitung Seite 8

Turning plate with footrest adapter (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Seatfix connection (for turning plate) (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Stabilising bow, rear (for turning plate) (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Stand, front (for turning plate) (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Back stabilisers (accessory)
The back stabilisers prevent the back from dropping. Please note our separate instructions for mounting! Download: www.thomashilfen.com
Footrest, short 12 cm / 4.7" (accessory)
Footrest, long 18 cm / 7.1" (accessory)
Remove the two caps at the front bottom part of the seat before attaching the footrest. Press the catch springs in at the rear ends of the sliding rods and push the tubes into
the holes as far as they will go.
USA version only! Always lock the footrest to the seat with the screw provided with the user manual. The receiver for the screw is located underneath the seat.
To stabilize the footrest on the vehicle floor adjust the height of the support bars by screwing them in or out until they have contact with the vehicle. Then lock the
support bars with the hand knobs to prevent them unscrewing accidentally. Screw the hand knobs upwards as far as possible and tighten them fast.
Please note: If the turning plate is being used the footrest is attached to the footrest adapter integrated in the turning plate. In this case, make sure to always secure the
footrest against falling off with the hand knob provided with the user manual. The receiver for the hand knob (metal block with thread) is situated on the left tube of the
footrest adapter.
Lower leg length: The lower leg length is adjusted by changing the height of the footrest. Loosen both outer screws. Retighten them after each adjustment.
Foot angle: Loosen the four screws left and right on the underside of the footrest to adjust the desired foot angle with the rails. Then retighten the screws.
Please note: The footrest cannot be used in combination with the seat depth extension.
Note: If the footrest should firmly be screwed to the seat, the "footrest adapter" (item code: 866) is required.
Fig. 6a: Caps + inserting the footrest
Seat wedge, bottom (accessory)
The seat wedge is positioned centrically below the car seat. The high edge is at the front to achieve an optimum rest position of the child.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Please note: Function of the turning plate is considerably reduced if being used in combination with the seat wedge. We therefore do not recommend using seat wedge
and turning plate at the same time.
Fig. 7a: Positioning seat on seat wedge
Seat wedge, inside (accessory)
The seat wedge (inside) can be fastened to the seat surface at 3 different positions:
1. An active posture is achieved by placing the seat wedge on the seat with the high side facing the back.
2. Velcro-fasten the seat wedge with the flat side facing rearwards for a more passive posture / rest position.
3. In order to reduce the seat depth or to achieve a bigger hip angle, you can also Velcro-fasten the seat wedge to the rear of the seat in an upright position with the broad
side facing downwards.
The two lateral pads for additional protection are Velcro-fastened to the sides.
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 8a: Active Fig. 8b: Passive
Seat depth extension + 13 cm / 5.1" (accessory)
USA version only! Attention: Before assembly of the seat depth extension, attach the safety screw provided with the user manual to the thread on the underside of the
seat. Before removing the seat depth extension, make sure to remove this safety screw again.
Remove the two caps at the front bottom part of the seat before attaching the seat depth extension. Press the catch springs in at the rear ends of the sliding rods and push
the tubes into the holes as far as they will go.
Please note: The seat depth extension cannot be used in combination with the footrest or turning plate.
The cover can be removed (cord) and washed in the machine at up to 30° C / 86° F.
Fig. 9a: Removing caps
Table (accessory)
Slide the table onto the two sides of the seat surface. The table is fastened on both sides with two Velcro strips each. Guide the Velcro strips of the table through the
plastic rings at the seat / seat back (pelvic belt).
The cover can be removed (zipper) and washed in the machine at up to 30° C / 86° F.
Fig. 10a: Attaching the table
8
RECARO Monza Reha – Instructions for assembly and use (supplement)
Fig. 6b: Adjusting height to vehicle
Fig. 7b: Final position
Fig. 8c: Back Fig. 8d: With lateral pads
Fig. 9b: Pressing in the catch springs
Fig. 10b: Attaching belts to seat
item code: 820
item code: 818
item code: 819
item code: 817
item code: 816
item code: 806
item code: 805
item code: 810
item code: 809
item code: 808
item code: 811