Cleaning Instructions - Bosch Runnʼn BGS4 serie Gebrauchsanleitung

Removing a blockage from the dust separation unit
26
Fig.
‡
Switch off the appliance.
a) Hold the appliance lid by the recessed handle and
open it.
b) Unlock the cover by turning it anti-clockwise, and
remove it from the appliance.
= Remove the blockage from the collecting unit. >
c) Put the cover back on and lock it in place by turning
it clockwise.
= Close the appliance lid. >
If the Sensor Control indicator continues to flash red,
check whether the nozzle, suction pipe or flexible hose
are blocked. This can also trigger the Sensor Control
indicator.
Exhaust filter care
Depending on the model, your appliance is equipped
with either a HEPA filter
Depending on the model, your appliance has additional
sound insulation behind the HEPA or micro filter. This
does not have to be cleaned.
HEPA filter
Cleaning a washable HEPA filter
The HEPA filter with the "washable" imprint is designed
so that it does not need to be replaced, provided the
appliance is used as intended in the household.
To ensure that the vacuum cleaner is working at its op-
timum power level, the exhaust filter should be rinsed
out after one year. The filtering action of the filter re-
mains intact, even if the filter surface becomes disco-
loured.
27*
Fig.
a) Open the lid of the exhaust filter by pushing and
pulling on the locking tab.
b) Unlock the HEPA filter and remove it from the ap-
pliance.
c) Tap out the filter unit and rinse it under running wa-
ter.
Alternatively, the unit can be cleaned in a washing
machine at max. 30 °C using a gentle programme
and the lowest spin speed.
TIP: To protect other laundry items, put the filter
unit into a laundry bag.
d) Once the HEPA filter has dried completely (at least
24 hours), insert it back into the appliance and lock
it in place.
= Close the exhaust filter lid. In doing so, push the >
lock bar upwards until it audibly clicks into place.
Micro filter
Cleaning the micro filter
The micro filter is designed so that it does not need to
be replaced, provided the appliance is used as inten-
ded in the household.
To ensure that the vacuum cleaner is working at its op-
timum power level, the exhaust filter should be rinsed
out after one year. The filtering action of the filter re-
mains intact, even if the filter surface becomes disco-
loured.
27 or a micro filter
Fig.
28*
Fig.
a) Open the lid of the exhaust filter by pushing and
pulling on the locking tab.
b) Pull the locking tab to unlock the filter unit with foam
filter and microfilter and remove it from the appli-
ance.
c) Remove the foam filter and microfilter from the filter
frame.
d) Rinse the foam filter and micro filter under run-
ning water. Alternatively, they can be cleaned
in the washing machine at max. 30 °C using a
gentle programme and the lowest spin speed.
TIP: To protect other laundry items, put the unit into
a laundry bag.
e) Once the foam filter and microfilter have dried com-
pletely (at least 24 hours), insert them back into the
filter frame.
f) Insert the filter unit in the appliance and ensure that
the locking tabs audibly click into place.
g) Close the exhaust filter lid. In doing so, push the lock
bar upwards until it audibly clicks into place.
28 .
Fig.

Cleaning instructions

Always switch off the vacuum cleaner and disconnect
the power cord from the mains before cleaning the va-
cuum cleaner. The vacuum cleaner and plastic acces-
sories can be cleaned with an ordinary plastic cleaner.
!
Caution:
Do not use abrasive materials, glass-cleaning
agents or all-purpose cleaning products. Never im-
merse the vacuum cleaner in water.
Subject to technical modifications.
* Dependent on model
47