Specifications - Makita 9556HN Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Switch lever
4-1. Wheel guard
4-2. Screw
4-3. Bearing box
5-1. Wheel guard
5-2. Bearing box
5-3. Screw
6-1. Lock nut

SPECIFICATIONS

Depressed center wheel diameter
Max. wheel thickness
Rated speed (n) / No load speed (n
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted
according to EN60745:
Model 9557HN, 9558HN
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745:
Explanation of general view
6-2. Depressed center grinding
wheel/Multi-disc
6-3. Inner flange
7-1. Lock nut wrench
7-2. Shaft lock
8-1. Lock nut
8-2. Abrasive disc
8-3. Rubber pad
10-1. Wire cup brush/Wire bevel brush
Model
Spindle thread
)
o
Overall length
Net weight
Safety class
noise level determined
) : 86 dB (A)
pA
) : 97 dB (A)
WA
value (tri-axial vector
9556HN
100 mm
6.4 mm
M10
11,000 min
271 mm
1.9 kg
ENE048-1
Model 9557HN
Work mode : surface grinding
Vibration emission (a
ENF002-2
Uncertainty (K) : 1.5 m/s
Work mode: disc sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model 9558HN
ENG905-1
Work mode : surface grinding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: disc sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
ENG900-1
The declared vibration emission value may also be
•
sum) used in a preliminary assessment of exposure.
The declared vibration emission value is used for
•
main applications of the power tool. However if the
power tool is used for other applications, the
vibration emission value may be different.
3
11-1. Lock nut
11-2. Abrasive cut-off wheel/diamond
wheel
11-3. Inner flange
11-4. Wheel guard for abrasive cut-off
wheel/diamond wheel
12-1. Exhaust vent
12-2. Inhalation vent
9557HN
115 mm
6.4 mm
M14 or 5/8"
(country specific)
-1 -1
11,000 min
271 mm
2.0 kg
/II
) : 7.5 m/s
h,AG
2
) : 2.5 m/s
h,DS
2
) : 8.5 m/s
h,AG
2
) : 2.5 m/s
h,DS
2
9558HN
125 mm
6.4 mm
M14 or 5/8"
(country specific)
-1
11,000 min
271 mm
2.1 kg
2
2
or less
2
2
or less
ENG902-1