Specifications; Safety Instructions - Makita 6953 Betriebsanleitung

ENGLISH
1 Socket
2 Anvil
3 Pin
4 O-ring
5 Switch trigger
6 Metal part
7 Handle
8 Reversing switch lever

SPECIFICATIONS

Model
Capacities
Standard bolt ...................................... 10 mm – 16 mm
High tensile bolt .................................... 8 mm – 12 mm
Square drive ...................................................... 12.7 mm
–1
No load speed (min ) ...................................... 0 – 3,000
Impacts per minute ........................................... 0 – 3,000
Max. fastening torque ........................................ 150 N•m
Overall length ..................................................... 233 mm
Net weight............................................................... 1.4 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for fastening bolts and nuts.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

SAFETY INSTRUCTIONS

WARNING! When using electric tools, basic safety
precautions, including the following, should always
be followed to reduce the risk of fire, electric shock
and personal injury. Read all these instructions
before operating this product and save these instruc-
tions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use
power tools in damp or wet locations. Keep work
area well lit. Don't use power tools in presence of
flammable liquids or gases.
3. Guard against electric shock
Prevent body contact with grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4. Keep children away
Do not let visitors contact tool or extension cord.
All visitors should be kept away from work area.
Explanation of general view
9 A side
10 B side
11 Clockwise
12 Counterclockwise
13 Expand
14 Hook
15 Fastening time
16 Seconds
5.
6953
6.
7.
8.
9.
10. Connect dust extraction equipment
11. Don't abuse cord
ENA001-2
12. Secure work
13. Don't overreach
14. Maintain tools with care
15. Disconnect tools
17 Proper fastening torque for
18 Fastening torque
19 Limit mark
20 Brush holder cap
21 Screwdriver
Store idle tools
When not in use, tools should be stored in dry,
high, or locked-up place, out of the reach of chil-
dren.
Don't force tool
It will do the job better and safer at the rate for
which it was intended.
Use right tool
Don't force small tools or attachments to do the
job of a heavy duty tool. Don't use tools for pur-
poses not intended; for example, don't use circu-
lar saw for cutting tree limbs or logs.
Dress properly
Do not wear loose clothing or jewelry. They can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommended when work-
ing outdoors. Wear protective hair covering to
contain long hair.
Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and
sharp edges.
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to oper-
ate tool.
Keep proper footing and balance at all times.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating
and changing accessories. Inspect tool cords
periodically and, if damaged, have repaired by
authorized service facility. Inspect extension
cords periodically and replace if damaged. Keep
handles dry, clean and free from oil and grease.
When not in use, before servicing, and when
changing accessories such as blades, bits and
cutters.
5