Specifications; Additional Safety Rules - Makita 9218SB Betriebsanleitung

ENGLISH
1 Side grip
2 Abrasive disc
3 Lock nut
4 Rubber pad

SPECIFICATIONS

Model
Max. capacities
Abrasive disc ....................................................180 mm
Wire cup brush ................................................ 110 mm
-1
No load speed (min ) ............................................ 4,500
Overall length ......................................................225 mm
Net weight ..............................................................2.7 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Always use eye and ear protection. Other per-
sonal protective equipment such as dust mask,
gloves, helmet and apron should be worn when
necessary. If in doubt, wear the protective equip-
ment.
2. Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
3. Accessories must be rated for at least the speed
recommended on the tool warning label. Wheels
and other accessories running over rated speed
can fly apart and cause injury.
4. Check the backing pad carefully for cracks, dam-
age or deformity before operation. Replace
cracked, damaged or deformed pad immediately.
5. Check that the workpiece is properly supported.
6. Hold the tool firmly.
7. Keep hands away from rotating parts.
8. Make sure abrasive disc is not contacting the
workpiece before the switch is turned on.
9. When sanding metal surfaces, watch out for fly-
ing sparks. Hold the tool so that sparks fly away
from you and other persons or flammable mate-
rials.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Pay attention that the wheel continues to rotate
after the tool is switched off.
12. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
4
Explanation of general view
5 Lock nut wrench
6 Wrench
7 Lock button
8 Switch trigger
13. If working place is extremely hot and humid, or
9218SB
14. Do not use the tool on any materials containing
15. Do not use water or grinding lubricant.
16. Ventilate your work area adequately when you
17. Always use the correct dust mask/respirator for
18. Ensure that ventilation openings are kept clear
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing side grip (auxiliary handle) (Fig. 1)
Screw the side grip on the tool securely.
Installing or removing abrasive disc (Fig. 2 & 3)
Important:
Always be sure that the tool is switched off and
ENB048-3
unplugged before installing or removing the disc.
Mount the rubber pad onto the spindle. Fit the disc on
over the rubber pad and screw the lock nut onto the spin-
dle.
To tighten the lock nut, hold the spindle with the wrench
so that it cannot revolve, then use the lock nut wrench
and securely tighten clockwise.
To remove the disc, follow the installation procedure in
reverse.
Switch action (Fig.4)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the trigger. Release the trig-
ger to stop. For continuous operation, pull the trigger and
then push in the lock button. To stop the tool from the
locked position, pull the trigger fully, then release it.
Operation (Fig. 5)
Hold the tool firmly. Turn the tool on and then apply the
abrasive disc to the workpiece.
In general, keep the abrasive disc at an angle of about
15° to the workpiece surface. Apply slight pressure only.
Excessive pressure will result in poor performance and
premature wear to the abrasive disc.
9 Limit mark
10 Screwdriver
11 Brush holder cap
badly polluted by conductive dust, use a short-
circuit breaker (30 mA) to assure operator safety.
asbestos.
perform sanding operations.
the material and application you are working
with.
when working in dusty conditions. If it should
become necessary to clear dust, first disconnect
the tool from the main supply (use non metallic
objects) and avoid damaging internal parts.