SSS Siedle BVPS 850-0 Produktinformation Seite 6

• Base plate pre-installable with
terminals
• Internal telephony with max. 6
indoor stations
• Doormatic (on/off)
• Can be used as a table top
unit using table-top accessory
ZTVP 850-...
Performance features
BVPC 850-0:
• 17.8 cm (7") touchscreen,
resolution 800 x 480 Pixel
• Integrated video memory, capacity
for over 2000 images with the sup-
plied SD card (4 GB)
• 15 switching/control functions in
conjunction with the bus switching
module BSM/BSE 650-..., selec-
tive dialling of door loudspeakers/
cameras
• 15 signal displays
• Optimized depiction of switching/
control functions and messages
• Voice volume adjustable in
3 stages
• Integrated audio and video privacy
device
• Status display with active speech
connection
• Optical call display by flashing of
the speech button
• Selective dialling of max. 15 door
loudspeakers/cameras
• Call silencing and status display
• Parallel switching of max. 8 indoor
stations
• Programming via PRI 602-... USB
and ZBVG 650-... possible
• Call differentiation for storey calls,
internal calls and 2 door calls
• 11 different electronic call tones to
chose from
• Call volume adjustable in 5 stages
up to max. 83 dB(A)
• Group formation for door calls.
Each BVPC 850-... can belong to up
to 5 groups in the same line
• Door release/light function at any
time using bus wires
• Door/video connection at any time,
also possible without prior door call
• Base plate pre-installable with
terminals
4
• Actuation of switching/control
functions in conjunction with
the bus switching module BSM/
BSE 650-...
• Feedback for switching/control
functions and messages in con-
junction with bus input module
BEM 650-...
• Internal telephony with max. 15
indoor stations
• Call forwarding
• Internal group call
• Collective announcement
• Automatic call pick-up with
internal call
• Doormatic on/off/time controlled
• Can be used as a table top
unit using table-top accessory
ZTVP 850-...
Electrical voltage
Mounting, installation and servicing
work on electrical devices may only
be performed by a suitably qualified
electrician.
Electrostatic charging
As a result of electrostatic charging,
direct contact with the circuit board
can result in destruction of the
device. Direct contact with the circuit
board must therefore be avoided.
Scope of supply
• BVPC/BVPS 850-... (Base plate and
housing with circuit board)
• operating instructions for the end
user
• this product information
Mounting
During installation, where applicable
ensure that the surface is protected
from damage.
1 Recommended mounting height
appr. 1.60 m to display height/
viewing height.
2 Open the device from the back
by releasing the base plate with the
locking lever.
3 Align the base plate centrally rela-
tive to the flush mounted box and
mark the fixing holes.
When mounting directly on the wall,
fasten the base plate using 4 screws,
paying attention that the plate is the
right way up (top marking).
4 Hook the housing into the base
plate from above and close by
exerting a slight pressure.
Dismantling
5 To remove the housing, press
the lock upwards using a flat blade
screwdriver. The circuit board
remains in the housing superstruc-
ture.
Terminal assignment
TaM Input
TbM In-Home bus
TaM Throughput
TbM In-Home bus
ERT Storey call button
Etb
+M Power supply
-M 20–30 V DC
S1 Potential-free contact
S1 freely programmable
Commissioning
• The basic configuration must be
carried out on every device without
fail.
• Installation and commissioning
procedures are described in the
system manual (enclosed with Bus
Video Line Rectifier BVNG 650-...).
• Functions on the user interface of
the deluxe bus video panel can be
individually named. Programming
takes place using the bus program-
ming software and is transferred to
the BVPC 850-... via the SD card. For
this, an SD card reader is required.