Energy Consumption; Prior To Use; Product Features - miniland baby digitalk luxe Bedienungsanleitung

accordance with the instructions, harmful interference
may occur in the radio communications.
However, it should be pointed out that it is impossible
to guarantee there will be no interference in a specific
installation. If the baby monitor causes interference to
the radio or television signal, which may be resolved
by turning it off and on again, the user should attempt
to deal with the interference as specified below:
· Change the position of the receiver (the parent unit)
or move it to a different place.
· Increase the distance between the interfering
equipment and the baby monitor.
· Plug the equipment into a circuit different to that the
receiver is plugged into.
· Contact the MINILAND S.A. customer service
department.
This equipment uses specially coated cables in order
to ensure compliance with RED Directive 2014/53/
EU. Using the device with non-approved equipment or
uncoated cables may cause interference to the radio
or television signal.
Any alteration or modification conducted by
personnel other than the MINILAND technical
department will render the product guarantee
invalid.

3.4. ENERGY CONSUMPTION

The power adapters supplied comply with the
European Union eco-design directive (Directive
2005/32/CE).
The consumption of energy is considerably lower
than the consumption of other adapters designed with
operation and standby modes.

3.5. PRIOR TO USE

Choosing the right place
· Place the baby unit away from televisions and TV
repeaters and radios. The signals generated by these
devices may cause noises or even sounds which are
retransmitted on the baby unit. If this occurs you will
need to place the baby unit somewhere else.
· The baby unit should be placed at least 3 metres
from the baby´s cot and on a flat surface. The baby
unit should never be placed in the cot, on the bed or
playground. Ensure the unit, cables and adapter are
all out of the reach of the baby and small children.
· Place the baby unit where the air is circulating freely,
and never on eiderdowns or blankets or on the edge
of a closet, shelf, etc
· Place the baby monitor away from sources of heat
such as radiators, chimneys, kitchens and direct
sunlight.

4. PRODUCT FEATURES

4.1. FEATURES AND CONTROLS OF THE
PARENTS' UNIT (Figure 1)
1. On/off button
2. Button to turn up volume
3. Nightlight button
4. Microphone
5. Speaker
6. Two-way button for talking to the baby unit
7. Button to turn down volume
8. Button to enable/disable the lullabies
9. LED on and loading indicator: with a fixed green light if
it is on or flashing green if the batteries are recharging
10.LED indicator showing low sound level: remains
off when no sound is detected at the baby unit or
flashes red if sound is detected (even if it is low) in
the baby's room
11.LED indicator showing high sound level: remains
off when the sound level detected in the baby's
room is low or flashing red when the baby's unit
detects a high sound level
12.Hole for neck strap
13.Battery compartment (2 x AAA 1.2V 800mAh Ni
MH rechargeable)
14.Charger-base
4.2. FEATURES AND CONTROLS OF THE BABY
UNIT (Figure 2)
15.Speaker
16.Nightlight button (short press)/parent unit search
(long press 3s)/transmission mode LOW/ZERO
(long press 5s)
17.LED on indicator/nightlight: it goes green when the
baby unit is on and has a more powerful white light
when the nightlight is enabled
18. On/off button
19. Microphone
20. Battery compartment (4 x AAA 1.5V alkaline, not
included)
21. Temperature sensor
22. VOX sensitivity switch (LOW/HIGH)
4.3. LCD SCREEN (Figure 3)
A. Battery level indicator
B. Nightlight indicator
C. Lullaby indicator
D. Volume indicator
E. Vibration mode indicator
F. Two-way mode indicator
G. Temperature
H. Coverage indicator
5. INSTRUCTIONS FOR USE
5.1. BEFORE USE: CONNECTION TO POWER
SUPPLY AND USE OF THE BATTERIES
Parents' unit:
The parents' unit of this baby monitor is designed to
work with the AC/DC adapters or batteries included.
It includes 2 rechargeable batteries x AAA 1.2V
800mAh Ni-MH for the parents' unit. We recommend
the use of the batteries in the parents' unit in order to
be able to hear the baby unit anywhere (within the
appliance's coverage radius).
The rechargeable batteries must be charged for at
least 16 hours before using them for the first time or if
they haven't been used for some time.
Put the baby unit at the charger base (14) where
possible to always keep the batteries charged.
- Take off the battery compartment cover (13) at
the rear of the parent unit, pressing and sliding
it downwards. Insert the rechargeable batteries
following the polarity marked on the unit itself and
closing the cover (Figure 4).
- Place the parent unit at the charger base (14)
(Figure 5).
- Plug the adapter in at the mains. The on and
charging LED (9) will flash green when charging.
The LED comes on green when the charging is
complete.
13
ENGLISH