Specifications - Makita JR180D Betriebsanleitung

ENGLISH
1 Battery cartridge
2 Push button
3 Charging light
4 Battery charger
5 Blade
6 Push button

SPECIFICATIONS

Model
Length of stroke ............................................. 23 mm
Strokes per minute .................................... 0 – 2,700
Cutting capacities
............................................................. 90 mm
Pipe
Wood ........................................................... 90 mm
Overall length ............................................... 447 mm
Net weight (with battery cartridge) .................. 3.5 kg
Rated voltage ............................................ D.C. 18 V
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
9. Do not operate charger if it has recieved a
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
4
Explanation of general view
7 Lever
8 Shoe
9 Loosen
0 Tighten
q Switch trigger
10. Do not disassemble charger or battery car-
JR180D
11. To reduce risk of electric shock, unplug
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1. Do not charge battery cartridge when tempera-
2. Do not attempt to use a step-up transformer,
3. Do not allow anything to cover or clog the
4. Always cover the battery terminals with the
5. Do not short the battery cartridge:
6. Do not store the machine and battery cartridge
7. Do not incinerate the battery cartridge even if
8. Be careful not to drop, shake or strike battery.
9. Do not charge inside a box or container of any
w Lock-off button
e Press in
r Limit mark
t Screwdriver
y Brush holder cap
tridge; take it to a qualified serviceman when
service or repair is required. Incorrect reas-
sembly may result in a risk of electric shock or
fire.
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
an engine generator or DC power receptacle.
charger vents.
battery cover when the battery cartridge is not
used.
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
in locations where the temperature may reach
or exceed 50°C (122°F).
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
kind. The battery must be placed in a well
ventilated area during charging.