Morphy Richards PREPSTAR Bedienungsanleitung Seite 28

FP401014MEE Rev1.qxp_Morphy Richards Instruction Book 31/07/2018 11:50 Page 28
Speed Dial Function
Pulse Mode
• Set the Speed Dial (3) to the 'P' position, then, press and hold the
Start/Stop Button (1).
• The unit will pulse at the max speed setting until the Start/Stop
button (1) is released.
• Use the Pulse Function when sudden bursts of speed are
required.
• Good for chopping sparsely to maintain a chunky consistency, eg.
for Salsas etc.
• Ideal for use with the Chopping Blade (20).
• Not recommended for use with the Grater Disc (13).
Speed Settings
• Set the Speed Dial (3) to the desired speed setting (1,2 or 3) and
press the Start/Stop Button (1) once to turn on.
• Once in use, you can cycle through the speed settings by turning
the Speed Dial (3) without having to press the Start/Stop Button
(1) again.
• To turn off the unit, press the Start/Stop button (1).
Pre-sets
• Set the Speed Dial (3) to the desired pre-set mode
and press the Start/Stop Button (1) once to turn on.
• Once in use, you can cycle through the pre-set modes and the
speed settings by turning the Speed Dial (3) without having to
press the Start/Stop Button (1) again.
• To turn off the unit, press the Start/Stop Button (1).
NOTE: Turning the Speed Dial (3) to the 'P' position whilst in use
stops the unit. The Start/Stop Button (1) must be held down to
use the Pulse Mode.
Presets on Speed Dial
Not recommended for use with the Grater Disc (13).
Preset 1
• Ideal for use with the Whisk (21).
• Good for mixtures that require a gradual start, such as
mayonnaise and whipped cream.
28
Preset 2
• Ideal for use with the Beater (19).
• Steady speed fluctuation allows for an even mixture and improved
incorporation in recipes like cake batter.
Preset 3
• Ideal for use with the Chopping Blade (20).
• Good for dry mixes, such as nuts and coffee beans, that require
the food to fall back into the bowl.
Before First Use
Before first use, carefully unpack your Prepstar Food Processor
and its attachments and remove any package material, labels or
stickers.
WARNING: Sharp blades.
Clean all the parts except the Motor Unit (4), following the
instructions in the 'Quick Cleaning' section.
CAUTION: Handle the blades with extreme care as they are
sharp.
Unpacking From Storage
Twist the Motor Unit (4) into the unlock position (
3
4 Then lift out the Motor Unit (4).
5 Twist the Bowl Lid (6) anti-clockwise to unlock, then lift.
Lift off the Grater Disc (13) from the Storage Bowl (10), and pull
6
the Storage Bowl (10) out from the Mixing Bowl (11). The Whisk
(21) is located underneath the Storage Bowl (10).
7 When reassembling, make sure to align the grooves of the Mixing
Bowl (11) and Storage Bowl (10), then slide the Storage Bowl (10)
into the Mixing Bowl (11).
Place the Bowl Lid (6) onto the Mixing Bowl (11), aligning the
8
grooves and twist clockwise to lock. Insert the Motor Unit (4) so
that the power cable is facing away from the Food Chute (8) and
twist clockwise to lock.
Assembly For Use
Push the Drive Shaft (9) up through the base of the relevant
9
accessory: Beater (19); Chopping Blade (20); Whisk (21).
WARNING:The Chopping Blade (20) is very sharp.
1 0 Lock the Drive Shaft (9) in place when in the accessory by
twisting it clockwise to attach to the accessory.
Unlock and remove the Drive Shaft (9) by twisting it anti-
clockwise and pulling it away from the base of the accessory.
1 1 Place the Drive Shaft (9) with locked accessory onto the Mixing
).