Scope Of Delivery; Assembly - Ikra GM AAS 4025 Gebrauchsanweisung

support. Never hold the machine above
shoulder height.
45. Special care must be taken in slippery
conditions (wet ground, snow) and in
difficult, overgrown terrain. Watch for
hidden obstacles such as tree stumps,
roots, rocks, holes and ditches to avoid
stumbling. For better footing, clear away
fallen branches, scrub and cuttings. Be
extremely cautious when working on
slopes or uneven ground.

Scope of delivery

• Remove the packaging material.
• Remove the packaging and/or transportation protec-
tion (if present).
• Verify that the delivery is complete.
• Check the unit and accessories for transportation dam-
age.
• If possible, store the packaging until the end of the
warranty period. After that period, please dispose of
the packaging in an environmentally friendly manner.
WARNING: The packaging material is not a play
toy! Please keep plastic bags out of the reach
of children. There is a risk of choking.
1x Chain saw attachment
1x Bar with Guide bar guard
1x Chain
1x Instruction manual
If parts are missing or damaged, contact your
dealer.

Assembly

Warning! Before assembling the device, remove
the battery.
1. Slide the pruner onto the tube (to do so, the screw
sleeve (8) must be loosened by turning anticlockwise).
2. Tighten the screw sleeve (8) by turning it clockwise to
attach the hedge trimmer to the tube.
Installing the bar and saw chain (Figs.
Attention! Danger of injury. Wear safety gloves
when fitting the chain. Always remove the
rechargeable battery from the device before
all work.
To install the bar and chain, no tools are needed for
this chain saw.
• Place the chainsaw on a stable surface.
• Turn the thumb screw (15) anti-clockwise to open the
chain wheel cover (16)
• Lay the saw chain (14) on the bar (13) and note the
running direction of the chain.
GB | Operating Instructions
• The cutting teeth must be on the top of the bar and
• Lay the free end of the saw chain over the chain drive
• Install the chain wheel cover (16) and turn the thumb
• Make sure that the chain tensioning bolt (19) sits pre-
• Then use the SDS chain tension ring (11) to set the
Tensioning the saw chain (Fig. 4)
a) Left direction: Tension chain
b) in the right direction: Loosen chain
If the device is equipped with SDS, this means that you
can loosen or tighten the chain and the bar (guide plate)
without having to use a tool. You can adjust the chain
tension using the chain tension ring (11) on the SDS.
You can use the thumb screw (15) on the SDS to loosen
or tighten the bar.
Unscrew the thumb screw (15) a little in an anticlockwise
direction. Then adjust the correct chain tension with the
SDS (11). Continue to tension the chain until it can be
lifted by around 3 mm in the middle of the strut as shown
in Fig. 4. Now tighten the thumb screw (15) completely.
Information on tensioning the chain
The saw chain must be correctly tensioned to ensure
safe operation. Optimum tension is reached when the
saw chain in the middle of the bar can be lifted up by 3
mm. Because the saw chain is heated by the sawing and
thus changing its length, check the chain tension every
10 minutes at the latest and adjust if necessary. This is
particularly true for new saw chains. Slacken the saw
chain after completing work because it shortens when
cooling. This prevents the chain being damaged.
Saw chain lubrication
2 and 3)
Filling the oil tank (Fig. 5)
1. Place the pruner on a level surface.
2. Clean the area around the oil tank lid and take it off.
10
facing forwards.
wheel (20) and the bar (13) with the elongated hole
over the bar guide.
screw (15) a little in a clockwise direction to fix the
cover hand-tight.
cisely in the small opening in the bar.
correct chain tension (see following section)
Attention! Always wear work gloves when you are
working on the chainsaw, to avoid injuries.
Attention: During the run-in time, the chain must
be re-tightened frequently. Immediately re-tighten
the chain if it flutters or hangs out of the groove.
Warning! Do not over-tension the chain as this
leads to excessive wear and decreases the ser-
vice life of the rail and chain.
Attention! Always wear work gloves when you are
working on the chainsaw, to avoid injuries.
Attention! Never operate the chain without saw
chain oil! Using chain saw without saw chain oil or
with an oil level below the minimum marking will
result in damage to the chain saw.
Attention! Only use special chain saw oil. The use
of used oil will render the warranty invalid.