Operation - Makita 2704 Bedienungsanleitung

the blade. Then tighten the hex bolts (B) to secure the
stay.
Fig.26
CAUTION:
If the blade and riving knife are not aligned properly,
•
a dangerous pinching condition may result during
operation. Make sure they are properly aligned.
You could suffer serious personal injury while using
the tool without a properly aligned riving knife.
NEVER make any adjustments while tool is
•
running. Disconnect the tool before making any
adjustments.
Don't remove the riving knife.
•
There must be a clearance of about 4 - 5 mm between
the riving knife and the blade teeth. Loosen the hex bolts
(A), adjust the riving knife accordingly and tighten the
hex bolts (A) securely. Attach the table insert on the
table, then check to see that the blade guard works
smoothly before cutting.
Fig.27
Installing and adjusting rip fence
Fig.28
1) Fit the hook on the tip of the rip fence into the far
guide rail on the table or sub table (R) and install and
push the rip fence forward so that the fence holder
engages with the nearmost guide rail.
To slide the rip fence on the guide rail sideways, pivot
the knob on the fence holder to the half way of its travel.
To secure the rip fence, pivot fully the knob on the fence
holder.
2) To slide the rip fence on the guide rail sideways,
return the knob on the fence holder fully without pulling
the lever on the knob.
3) To remove it, pull the lever on the knob and pivot the
knob fully forward while pulling the lever.
To check to be sure that the rip fence is parallel with the
blade, secure the rip fence 2 - 3 mm from the blade.
Raise the blade up to maximum elevation. Mark one of
the blade teeth with a crayon. Measure the distance (A)
and (B) between the rip fence and blade. Take both
measurements using the tooth marked with the crayon.
These two measurements should be identical. If the rip
fence is not parallel with the blade, proceed as follows:
Fig.29
Fig.30
1. Position the rip fence in the sliding position.
2. Loosen the two hex bolts on the rip fence with the
hex wrench provided.
3. Adjust the rip fence until it becomes parallel with
the blade.
4. Pivot down the knob on the rip fence toward the
operator.
5. Tighten the two hex bolts on the rip fence.
Fig.31
CAUTION:
Be sure to adjust the rip fence so that it is parallel
•
with the blade, or a dangerous kickback condition
may occur.
When the rip fence cannot be secured solidly, adjust it
according to the following procedure.
(1) Set the rip fence on the table and then pivot
the knob on the half way of its travel (moving
position). Tighten the screw (A) until the rip
fence is immobilized. Then loosen a 1/4 to
1/2 turn.
Fig.32
Fig.33
(2) Tighten the screw (B) fully and then loosen
about 2 full revolutions.
(3) Lock the rip fence by fully pivoting the knob
on the fence holder (lock position).
(4) Make sure that the rip fence can be installed
and removed
(released position).
(5) Make sure that the rip fence can be slid
smoothly with no wobble when the knob is on
half way of its travel.
CAUTION:
Be careful not to tighten screws with more than
•
tightening amount
instructions. Failure to do so may damage the
fastened parts.
Bring the rip fence up flush against the side of the blade.
Make sure that the guideline on the fence holder points
to the 0 graduation. If the guideline does not point to the
0 graduation, loosen the screw on the scale plate and
adjust the scale plate.
Fig.34
Connecting to vacuum cleaner
Cleaner operations can be performed by connecting the
tool to Makita vacuum cleaner or dust collector.
Fig.35

OPERATION

CAUTION:
Always use "work helpers" such as push sticks and
•
push blocks when there is a danger that your
hands or fingers will come close to the blade.
Always hold the workpiece firmly with the table and
•
the rip fence or miter gauge. Do not bend or twist it
while feeding. If the workpiece is bent or twisted,
dangerous kickbacks may occur.
NEVER withdraw the workpiece while the blade is
•
running. If you must withdraw the workpiece before
completing a cut, first switch the tool off while
holding the workpiece firmly. Wait until the blade
has come to a complete stop before withdrawing
the workpiece. Failure to do so may cause
11
in the original position
specified in the above