Eurosystems Sandy Bedienungsanleitung Seite 11

4. Before start to operate the unit, check carefully the feeding cable. In case the feeding
EN
cable shows to be damaged do not use the motor-brush: verify first the damage , make up
for it : do not put the plug into the socket.
5. The section of the mains cable must be the same or higher if compared to class 05 RN. The
value of the mains supply current to which the machine is to be connected must correspond
to the data shown on the machine label. For safety reasons, a 10A circuit breaker and a
nominal 10/30 mA automatic cut-out must be installed on the power line.
6. motor-brushes assembly disassembly, cleaning, servicing operations must be performed
when the engine is switched off and the plug removed from the socket.
7. Start the motor-brush standing behind the handlebars. The operator's position must be
the same ( i.e. standing behind) even during brushing operations. Do not work backwards,
as there is risk of falling. Please walk, never run with the machine and avoid any position
which could cause lost of balance.
8. Do not touch/change the safety/protection devices. If the operator releases the lever
(Fig.4 - part.2), the motor and the brush must switch off
9. the brushes when turning can be a danger for the feet. Wear solid/suitable closed shoes
and long trousers and do not get near to the cultivator blades. Do not use the unit when
barefooted or wearing sandals.
10. Check the area to be worked to be free of foreign bodies , stones, piece of wood, roots,
etc and in case remove them . Pay great attention to any other object you can meet on your
path during brushing operations. Do not use the machine on ground containing large stones.
11. In the case of an obstacle being hit which stops the machine, contact a service dealer
to check it.
12. If the operator needs to move the motor-brush ,it must be switched off and wait for
brushes standstill. Do not leave the motor-brush unattended in the work area.
13. Do not store the motor-brush with plug inserted in the socket.
14. Do not use the motor-brush when it is raining, or in wet and damp weather. Do not sprinkle
water on the machine and keep it protected from humidity. Do not use the motor-brush near
ponds, swimming pool and water in general.
15. Modifications or make-shift repairs on the machine are absolutely forbidden.
16. Please note that our company assumes no responsibility for damages due to: a) repairs
made by unspecialized/unauthorized after sales service centres and/or (b) use of other than
ORIGINAL SPARE PARTS.
ASSEMBLY INSTRUCTIONS:
packaging (if not differently agreed). To complete the assembly, please do the following steps:
HANDLEBARS ASSEMBLY (fig. 2)
frame (11) fix it with two screws (8), four washers (9) and two nuts (10). Insert the wire cable holder
(12) into the left handlebar tube. Fix the two handles (1-2) to the tube (3) separated from items (6),
fixing with the screws (4), the washers (7) and the handles (5).
All components are included into the packaging box.
SWITCH ASSEMBLY (Fig. 3) :
handlebar as shown in the picture . Close the switch opening-side and fix it using the 2 self-tapping
screws (in the accessories envelope).
ADJUSTMEnTS
HANDLEBARS ADJUSTMENT : (Fig. 2)
according to our own needs. Such operation is possible by screwing up the tubes (1 and 2) in points
A or B. In order to transport the motor-brush on a vehicle , you can disassemble the 2 handlebars
by loosing the handles (5).
IMPORTANT - when you transport the machine on a vehicle you should position it where it won't
12
cause any damage to nobody. Block it tightly to avoid the unit to overturn, to get damaged and avoid
also some oil leaks from the transmission.
the unit is received at destination disassembled in a suitable
Insert the lower handle (3) into the two holes of the
Fix the switch putting the 2 plastic pins into the holes of the
upper handlebar can be adjusted in height