Specifications; Additional Safety Rules - Makita 9564CVL Betriebsanleitung

ENGLISH
1 Abrasive disc
2 Pad
3 Spindle
4 Switch lever
5 Speed adjusting dial
6 Screw

SPECIFICATIONS

Model
Abrasive disc ............................................................................... 115 mm
Spindle thread ............................................................................. M14
-1
No load speed (min ) .................................................................. 2,000 – 6,800
Overall length .............................................................................. 311 mm
Net weight .................................................................................... 1.8 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Always use eye and ear protection. Other per-
sonal protective equipment such as dust mask,
gloves, helmet and apron should be worn when
necessary. If in doubt, wear the protective equip-
ment.
2. Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
3. Keep guards in place when using as a grinder.
4. Use only wheels with correct size and wheels
having a maximum operating speed at least as
high as the highest No Load Speed marked on
the tool's nameplate.When using depressed cen-
ter wheels, be sure to use only fiberglass-rein-
forced wheels.
5. Check the backing pad or the wheel carefully for
cracks or damage before operation. Replace
cracked or damaged pad or wheel immediately.
6. Observe the instructions of the manufacturer for
correct mounting and use of wheels. Handle and
store wheels with care.
7. Do not use separate reducing bushings or adap-
tors to adapt large hole abrasive wheels.
8. Use only flanges specified for this tool.
9. Do not damage the spindle, the flange (espe-
cially the installing surface) or the lock nut. Dam-
age to these parts could result in wheel
breakage.
Explanation of general view
7 Head cover
8 Gear housing
9 Screw
10 Wheel guard
11 Notch
12 Press
10. For tools intended to be fitted with threaded hole
11. Before using the tool on an actual workpiece,
12. Check that the workpiece is properly supported.
13. Hold the tool firmly.
14. Keep hands away from rotating parts.
15. Make sure the abrasive disc or the wheel is not
16. Use the specified surface of the wheel to per-
ENB038-5
17. Do not use cutting off wheel for side grinding.
18. Watch out for flying sparks. Hold the tool so that
19. Pay attention that the wheel continues to rotate
20. Do not touch the workpiece immediately after
21. Position the tool so that the power cord always
22. If working place is extremely hot and humid, or
23. Do not use the tool on any materials containing
24. Do not use water or grinding lubricant.
25. Always use the correct dust mask/respirator for
26. Ensure that ventilation openings are kept clear
SAVE THESE INSTRUCTIONS.
13 Shaft lock
14 Lock nut
15 Depressed center wheel
16 Inner flange
17 Lock nut wrench
18 Tighten
9564CVL
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
test run the tool at the highest no load speed for
at least 30 seconds in a safe position. Stop
immediately if there is any vibration or wobbling
that could indicate poor installation or a poorly
balanced wheel. Check the tool to determine the
cause.
contacting the workpiece before the switch is
turned on.
form the grinding.
sparks fly away from you and other persons or
flammable materials.
after the tool is switched off.
operation; it may be extremely hot and could
burn your skin.
stays behind the tool during operation.
badly polluted by conductive dust, use a short-
circuit breaker (30 mA) to assure operator safety.
asbestos.
the material and application you are working
with.
when working in dusty conditions. If it should
become necessary to clear dust, first disconnect
the tool from the main supply (use non metallic
objects) and avoid damaging internal parts.
9565CVL
125 mm
M14
2,000 – 6,800
311 mm
1.8 kg
5