Specifications - Makita DPJ140 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Button
1-2. Red indicator
1-3. Battery cartridge
2-1. Star marking
3-1. Indication lamp
4-1. Pointer
4-2. Stopper
4-3. Adjusting screw
4-4. Rubber spike
5-1. Lock lever
5-2. Angle guide
5-3. Knob
5-4. Scale
5-5. Pointer
5-6. Tighten
5-7. Loosen
6-1. Knob
6-2. Down
6-3. Up

SPECIFICATIONS

Max. grooving depth
No load speed (min
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting crescent shaped slots for
the placement of flat wooden dowels or biscuit by a
plunging action.
Noise
The typical A-weighted
according to EN60745:
Model DPJ140
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model DPJ180
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Explanation of general view
6-4. Center of blade thickness
7-1. Fence
7-2. Angle scale
7-3. Lock lever
7-4. Tighten
7-5. Loosen
8-1. Lock lever
8-2. Pointer
8-3. Angle scale
8-4. Center of blade thickness
8-5. Blade cover
9-1. Lock lever
9-2. Pointer
9-3. Angle scale
9-4. Set plate
9-5. Thickness of set plate
9-6. Center of blade thickness
9-7. Blade cover
10-1. Set plate
Model
Type of blade
-1
)
Overall length
Net weight
Rated voltage
noise level determined
) : 73 dB (A)
pA
) : 74 dB (A)
pA
DPJ140
D.C. 14.4 V
ENE013-1
Vibration
The vibration
determined according to EN60745:
ENG905-1
Work mode : cutting grooves in MDF
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
5
11-1. Slide switch
12-1. Lock nut
12-2. Plate joiner blade
12-3. Blade cover
12-4. Inner flange
12-5. Clamp screw
12-6. Shaft lock
12-7. Loosen
12-8. Tighten
13-1. Dust bag
13-2. Fastener
13-3. Dust nozzle
28-1. Exhaust vent
28-2. Inhalation vent
29-1. Limit mark
30-1. Holder cap cover
30-2. Screwdriver
31-1. Brush holder cap
31-2. Screwdriver
DPJ180
Plate joiner
20 mm
6,500
351 mm
3.0 kg
D.C. 18 V
total value (tri-axial
2
) : 2.5 m/s or less
h
2
ENG900-1
vector sum)
ENG901-1