grandimpianti WR 11 Installations- Und Gebrauchsanweisung Seite 18

www.groupdynamics-laundry.com
sales@groupdynamics.lv
Pressing "PROG" again will cause the display
to read "F1" (on the time display), which
stands for the first function that applies to
cycle 1.
Press "PROG" again to pass on to "F2", and
so on to the last function, "Ge".
Press "PROG" once more to exit the
programming mode and save the changes.
WARNING: if a potential drop should occur
during a programming session, changes will
not be saved and it will be necessary to
repeat the programming procedure from the
beginning.
When a cycle is underway, the "PROG" key
causes the machine to pause and does not
give access to the programming mode.
The PROG key stops the cycle at whatever
the stage underway except the while
spinning.
The DISPLAYS will then read "PAUSE"
and the machine will stay like this until the
"START" key is pressed and the cycle is
resumed.
WARNING!
-)This function is available only when a
cycle is in progress.
-)Pauses cause heating to go off too, which
means that long stops will cause the
temperature to drop.
PROGRAMMING
Options from F0 to F9 as well as Ci, L0 and
GE can be enabled individually and cycle by
cycle. Functions stay enabled permanently
until the user chooses to disable them.
The programming mode can be accessed
only with the door closed and with non coin-
operated machines.
While programming, the cycle display reads
the cycle (from 1 to 9) and the time display
reads "Fy", where y is the selected function.
The selection appears on the temperature
display; 0 = disabled, 1 = enabled; some
functions may have more options (cfr.
specific description below).
As usual, a cycle is selected by pressing the
"P" key, whereas options are selected through
the PROG key and enabled or disabled through
the "+" and "-" keys respectively.
When the PROG key is pushed repeatedly,
options are shown in a cyclic sequence from
F1 to GE and then back to the current selection.
The stored cycles are scrolled by pressing the
"P" key (minimum 1, maximum 9).
IMPORTANT !!!
When an option is selected for a cycle that
does not envisage it (see description of
individual options) the machine will accept
the selection but the corresponding
function will not be carried out.
PROGRAMMIMG BY PC
Washers can also be programmed via PC,
though a serial port. For this purpose the
machine's control board, accessible by
opening the hood, has a port for the
connection of a cable that can be supplied by
the after-sales service (cfr. specific
instruction on the connection kit).
To enable the "data transmission and reading"
mode it will be necessary to switch the
washer on while holding down the "PROG"
key: the displays will only read "HC".
For further details, contact your seller or the
after-sales service.
WARNING!
Do not try to read or change machine
programming, unless you have the ad-
hoc cable supplied by the manufacturer,
as this could cause severe damage to the
electronic boards.
If you wish to change machine programming,
contact your seller or the after-sales service.
DESCRIPTION OF PROGRAMMABLE
FUNCTIONS
Cool-down (F1)
As a rule at the end of a high-temperature
wash cycle (above 60°C) soft water is taken
in in order for the temperature inside the
drum to decrease gradually. When this
parameter is set to "1", and the selected cycle
features it, this procedure is not carried out.
Value Function
0 Normal (default).
1 NO cool-down
This function can be enabled for every single
cycle.
Change spinning stage (F2)
The final spinning can be changed from 1
minute up to 8 minutes. This function
modifies the length of final spinning. If the
setting assigned to this function is 9, spinning
will totally be eliminated.
Value Function
0 Normal (default)
18
1 1 minute spinning
2 2 minute spinning
3 3 minute spinning
4 4 minute spinning
5 5 minute spinning
6 6 minute spinning
7 7 minute spinning
8 8 minute spinning
9 No spinning
This function can be enabled for every single
cycle.
No prewash (F3)
When this function is enabled the prewash
step is excluded.
Value Function
0 Normal (default).
1 NO prewash
This function can be enabled for every single
cycle.
Deferred cycle start (F4)
Postpones the start of a wash cycle and
determines cycle delay.
If the value assigned to this function is other
than zero, as soon as the programming session
is exited the time DISPLAY will blink the
hours and the temperature DISPLAY will
blink the minutes, whereas the cycle display
will read the selected wash program.
To start the countdown, just press the START
push-button: the displays will be lit
continuously.
As soon as the countdown is over, the cycle
will start automatically and the displays will
resume their usual functions.
Before the START push-button is pressed
and during the count-down all keys are
enabled.
IMPORTANT !!!
Time is displayed in the "HH.MM"format.
H stands for hours and M for tens of minutes.
Unit: hours and minutes
Range: 00h00'...23h50'
(00.00...23.50)
Resolution: 10 min.
(0.1)
Default: 00h00'
Caution:
When pressed, the START key excites the
CYCLE relay and the door is automatically
locked.
If the door is not closed correctly, the "door"
alarm will warn the user. If the door fails to
be locked, alarm "E6" trip.
In the latter case it will be necessary to
proceed as follows: press START once, solve
the problem (if possible) and press START
once again to set the machine to work.
If a deferred start is cancelled (by entering
the programming mode and setting F4 to
00.00) the door will be automatically
unlocked.
Enable/disable BUZZER (F5)
This function enables/disables the buzzer,
which can be completely eliminated from all
cycles except for alarms.
Value Function
0 Normal (default).
1 No buzzer