Zulassungen; American Bureau Of Shipping (Abs) - Hilti S-BT-MR M8/7 SN 6 AL Technisches Handbuch

7. Zulassungen

7.1 American Bureau of Shipping (ABS)
Please refer to the "Service Restrictions" shown below to determine if Unit Certification is required for this product.
This certificate reflects the information on the product in the ABS Records as of the date and time the certificate is
printed.
Pursuant to the Rules of the American Bureau of Shipping (ABS), the manufacturer of the below listed product held
a valid Manufacturing Assessment (MA) with expiration date of 30/AUG/2021. The continued validity of the
Manufacturing Assessment is dependent on completion of satisfactory audits as required by the ABS Rules.
And; a Product Design Assessment (PDA) valid until 18/SEP/2021 subject to continued compliance with the Rules
or standards used in the evaluation of the product.
The above entitle the product to be called Product Type Approved.
The Product Design Assessment is valid for products intended for use on ABS classed vessels, MODUs or facilities
which are in existence or under contract for construction on the date of the ABS Rules used to evaluate the
Product.
ABS makes no representations regarding Type Approval of the Product for use on vessels, MODUs or facilities
built after the date of the ABS Rules used for this evaluation.
Due to wide variety of specifications used in the products ABS has evaluated for Type Approval, it is part of our
contract that; whether the standard is an ABS Rule or a non-ABS Rule, the Client has full responsibility for
continued compliance with the standard.
Model Name(s): S-BT screw-in stainless steel threaded fasteners: S-BT-MR M10,
S-BT-MR W10, S-BT-MR M8, S-BT-GR M8; S-BT screw-in carbon steel threaded
fasteners: S-BT-MF M10, S-BT-MF W10, S-BT-MF M8, S-BT-GF M8; Composite
Presented to:
HILTI AKTIENGESELLSCHAFT
FELDKIRCHERSTR. 100
Liechtenstein
Intended Service:
Description:
10/12/2016 5:02:08 AM
Tests und Berichte
Confirmation of Product Type Approval
Product Name: Fastening System
Fasteners: X-FCM-R and X-FCM-M
For fastening of fastened materials to base materials of carbon steel or aluminum
in the Ship and Shipbuilding environment and in Offshore Structures.
1. In the S-BT fasteners, the threaded stud is set into a small pre-drilled pilot hole
and the drill entry point is then completely sealed by the stud washer during
setting. This doesn't require any rework of the protective surface coating because
there is no through penetration of the base material. 2. For the S-BT System there
is also the possibility to set the stud into a drill through hole in thin base material. In
this case a rework of the protective surface on the backside is potentially needed.
3. Dimensions and material specifications of S-BT fasteners: refer to the Data
Sheet ("Hilti S-BT Direct Fastening Technology Manual 08/2016"). 4. The fasteners
are to be installed and inspected using installation procedures and tools
recommended by the manufacturer as in the Data Sheet: a) Drilling tool: SF BT
18-A or SF BT 22-A; b) Drill bits: TS-BT 4.3-74 S, TS-BT 5.5-74 S, TS-BT 5.5-74
AL. 5. Base material thickness tII and type of bore hole: a) Pilot hole, base material
steel: tII >= 5 mm [0.20"]; b) Pilot hole, base material aluminum: tII >= 6 mm [0.24"];
c) Drill through hole, base material steel: 6 mm [0.24"] > tII >= 3mm [0.12"]; d) Drill
through hole, base material aluminum: 6 mm [0.24"] > tII >= 5mm [0.20"]. 6.
Composite fasteners are either made from stainless steel (X-FCM-R) or from
Copyright 2001 American Bureau of Shipping. All rights reserved.
S-BT-Gewindeschraubbolzen zum Einschrauben
Certificate Number: 16-HS1550085-PDA
12/OCT/2016
Page 1 of 3
51