Before Use; Operation - Hilti TE 905-AVR Bedienungsanleitung

6. Before use

Ensure that the tool is disconnected from the mains
supply.
en
6.1 Fitting the side handle
1. Fit the side handle and side handle clamp onto the
tool.
2. Secure the side handle by tightening the screw knob.
6.2 Use of extension cords
Use only extension cords of a type approved for the appli-
cation and with conductors of adequate cross section.
Recommended minimum conductor cross section and
max. cable lengths:

7. Operation

Never use the tool without the side handle.
Use a vice or clamp to secure loose workpieces.
7.1 Adjusting the side handle
1. Unplug the supply cord from the mains socket.
2. Slacken the screw knob on the side handle.
3. Bring the side handle into the desired position.
4. Tighten the screw knob to secure the side handle in
the desired position.
7.2 Fitting the insert tool
-NOTE-
The chisel can be locked in the chuck in 6 different posi-
tions (in 60° increments).
Flat and shaped chisels can thus always be brought into
the optimum position for the job on hand.
1. Unplug the supply cord from the mains socket.
2. Check that the insert tool connection end is clean and
lightly greased. Clean and grease the connection end
if necessary.
3. Check that the sealing lip on the dust cap is clean and
in good condition. Clean the dust cap if necessary or
replace it if the sealing lip is damaged.
4. Push the insert tool into the chuck and rotate it while
applying light pressure until it engages in the guide
grooves.
16
Printed: 07.07.2013 | Doc-Nr: PUB / 5071242 / 000 / 00
Mains voltage Conductor cross section
1.5 mm 2 2.0 mm
100 V – 20 m
110–120 V 20 m 25 m
220–240 V 50 m –
Do not use extension cords with 1.25 mm
conductor cross sections.
6.3 Use of a generator or transformer
This tool may be powered by a generator or transformer
which fulfils the following conditions:
– AC voltage output, power output at least 3200 W
– The operating voltage must be within +5% and –15%
of the rated voltage at all times.
– Frequency range 50–60 Hz, never above 65 Hz
– Automatic voltage regulation with starting boost
Never operate other tools or appliances from the generator
or transformer at the same time. Switching other tools
or appliances on and off may cause undervoltage and /
or overvoltage peaks, resulting in damage to the tool.
5. Push the insert tool into the chuck until it is heard to
engage.
6. Check that the insert tool is held securely by attempt-
ing to pull it out of the chuck.
7.3 Removing the insert tool
-CAUTION-
– The insert tool may become hot during use. There is
a risk of burning the hands. Wear protective gloves
when changing insert tools.
1. Unplug the supply cord from the mains socket.
2. Open the chuck by pulling back the locking sleeve.
3. Pull the insert tool out of the chuck.
7.4 Chiseling
– The power tool and the chiseling operation emit noise.
Excessive noise may damage the hearing. Wear ear
protection.
– Chiseling may cause splintering of the material. Splin-
ters may cause injury to parts of the body and eyes.
Wear eye protection, protective gloves and breath-
ing protection if no dust removal system is used.
-NOTE-
When working at low temperatures: The hammering
mechanism works only when the tool has reached a min-
imum operating temperature. Bring the drill bit into con-
AWG
2 2.5 mm 2 3.5 mm 2 14 12
– 30 m – –
30 m – 75 ft 125 ft
100 m – – –
2 or 16 AWG