Before You Begin; Door Types; Tools Required; Hardware Provided - LiftMaster LM60 serie Anleitungen

Before You Begin

1. Look at the wall or ceiling above the garage door. The header
bracket must be securely fastened to structural supports.
2. Do you have a finished ceiling in your garage? If so, a support
bracket and additional fastening hardware (not supplied) may be
required.
3. Depending on your door's construction, you might need a special
door arm. See your dealer.
4. Do you have an access door in addition to the garage door? If
not, Model 1702E Outside Quick Release Accessory is required.
1

Door Types

A. One-Piece Door with Horizontal Track Only.
B. One-Piece Door with Horizontal and Vertical Track – Special door
arm (E, The Chamberlain Arm™) and The Protector System™
required. See your dealer.
C. Sectional Door with Curved Track – See 20B – connect door arm.
The Protector System™ is required for doors that are over 2.5m in
height.
D. Canopy door – Special door arm (E, The Chamberlain Arm™)
and The Protector System™ required. See your dealer.
E. The Chamberlain Arm™ for use on door types B and D.

Tools Required

2

Hardware Provided

3
(1) Hex Bolt
(2) Clevis Pin
(3) 8mm Carriage Bolt
(4) Wood Screws
(5) Sheet Metal Screws
(6) Clevis Pin
(7) Rope
(8) Handle
(9) Insulated Staples
(10) Anchor
(11) Concrete Anchor

Completed Installation

4
As you proceed with the assembly, installation and adjustment
procedures in this manual, you may find it helpful to refer back to
this illustration of a completed installation.
(1) Header Sleeve
(2) Idler Pulley Bracket
(3) Trolley
(4) Rail
(5) Chain/Belt
(6) Hanging Bracket
(7) Power Cord
(8) Opener
ASSEMBLY SECTION
IMPORTANT: If you have a canopy door, you need to use the
instructions packed with The Chamberlain Arm™ Accessory in
conjunction with this Owner's Manual when assembling the rail.
Assemble the Rail
5
Grease inside edges of rail sections using grease (1). Place rail pieces
(2) on flat surface for assembly. All four rail sections are
interchangeable. Slide rail brace (3) onto rail section. Connect rail by
sliding rail brace onto next rail section. Tap rail assembly (4) on piece
of wood (5) until rail sections are flush. Repeat with remaining rail
sections.
(12) Lock Washer
(13) Hex Nut
(14) Ring Fastener
(15) Metric Tapping Screw
(16) Hex Screw
(17) Stop Bolt
(18) Spring
(19) Flat Washer
(20) Lock Nut
(21) Rail GreaseFlat
(9) Light Lens
(10) Manual Release
Rope & Handle
(11) Curved Door Arm
(12) Straight Door Arm
(13) Door Bracket & Plate
(14) Header Bracket
(15) Trolley Release Arm
Install the Chain/Belt
6
Remove chain/belt from carton and lay chain out on floor (do not allow
chain/belt to twist).
A. Chain: Push pins of master link bar (3) through chain link (4) and
hole in trolley (5). (see picture) Push cap (2) over pins and onto
notches. Slide clip-on spring (1) over cap and onto pin notches until
both pins are securely locked in place.
B. Belt: Hook the trolley connector (6) into the slot (7) on the
trolley (8).
Insert Trolley & Idler Pulley Bracket into
7
Rail
Slide idler pulley bracket (1) and inner trolley (2) into back (opener)
end of rail assembly (3), be sure to insert idler pulley bracket as
shown. Arrow on trolley (7) must face toward front (header) end of rail
(4). Push idler pulley bracket toward front (header) end of rail (4).
Insert carriage bolt (5) into bolt cut out in the idler pulley bracket (6).
Attach Trolley to Rail
8
Slide outer trolley (1) into back (opener) end of the rail assembly (2),
be sure end with trolley release arm (3) is heading in direction of
opener. Slide outer trolley down rail until it engages with inner trolley.
Fasten Rail to Opener and Install
9
Chain/Belt
Remove four washered bolts (1) from top of opener. Place rail (2) on
opener, flush with stop (3) on top of opener. Wrap chain/belt (4) over
sprocket (5). Push idler pulley bracket assembly toward front of the rail
to eliminate excess slack in chain/belt. Align bolt holes on brackets (6)
with bolt holes on opener. Secure brackets to opener with previously
removed bolts. Tighten bolts securely. The opener sprocket teeth
must engage the chain/belt.
CAUTION: Use only those bolts mounted in the top of opener.
Use of any other bolts will cause serious damage to opener.
Attach Sprocket Cover
10
Place sprocket cover (1) on top of the opener (2), secure with screws
(3). Insert bolt (4) into trolley stop hole (5), secure with washer (6) and
nut (7).
Assemble Header Sleeve and Tighten
11
Chain/Belt
Slide header sleeve (1) onto rail (5). Slide flat washer (3), spring (2)
and washer (3) onto carriage bolt (4). Thread nut (6) onto carriage bolt
until finger tight. Use an open end wrench (7) to tighten nut until the
chain/belt is approximately 2mm above the base of the rail at its
midpoint. DO NOT OVER TIGHTEN THE CHAIN OR BELT. See
image (8).
INSTALLATION SECTION
Wear protective goggles when working overhead to protect your
eyes from injury.
Disengage all existing garage door locks to avoid damage to the
garage door.
To avoid serious personal injury from entanglement, remove all
ropes connected to the garage door before installing the opener.
It is recommended that the opener be installed 2,1m (7 feet) or more
above the floor where space permits.