Installation And Removal - Grundig 5101 RDS Serviceanleitung

Coding
Information about coding Activating coding
Your personal code number is on the identity 1. The expert mode is switched on and
card of your car radio. "CODE" appears in the display.
Coding is not activated when the radio leaves Activate the setting:
the factory. "
LOUD
Briefly press the
EXPERT
If you have "activated" your car radio's
The display indicates "
coding:
2. Enter the code number (on the Identity
As soon as you disconnect the car radio from
Card):
the car battery (or permanent plus terminal
Repeatedly press the buttons
30), it is electronically blocked.
until the code number is shown in the dis-
Only you are able to put it back into operation
play.
by entering your personal Code Number.
Example: 1703
If the Code Number is lost (Identity Card),
"
Button 11 brief pressure
only a dealer can put the radio back into 1
"
17 brief pressures >1 7 - -<
Button 2
operation after you provide proof of owner-
"
Button 10 brief pressures >1 7 0 -<
ship and pay a fee. 3
"
13 brief pressures >1 7 0 3<
Button 4
When pressing a longer time, the correspon-
Is the coding activated?
ding figure counts backwards.
Activate the expert mode and turn the 3. Confirm the code number:
¢ ¢
rotary knob until the display indicates "
LOUD
Briefly press the
EXPERT
"SAFE" or "CODE".
display indicates "SAFE".
"SAFE" Coding activated.
Coding is activated!
"CODE" Coding not activated.
4. Quit the expert mode.
A4 +12 V ignition voltage
Supply voltages
Connect to terminal 15 or terminal 30 of the
+
Blade contacts A: Figure vehicle:
A8 – operating voltage (earth)
– Terminal 15, if you wish to switch the car
Connect to terminal 31 (earth) of the vehicle.
radio on and off with the ignition/start
switch.
A7 +12 V operating voltage
Connect to terminal 30 (permanent plus) of
– Terminal 30, if you do not wish to switch
the vehicle. the car radio on and off with the
ignition/start switch.
A6 Instrument illumination
Connect the blade contact A6 to terminal 58
A2 Phone connector (Mute)
of the vehicle:
for car telephone or CB radio:
When the vehicle's headlights are switched on
The car radio is "muted" when the car tele-
and the car radio is switched off, the illumina-
phone or CB radio is in operation.
tion of of the car radio controls can be set
The display indicates "MUTE"
with the instrument illumination control.
For this, the blade contact A2 must be
connected from the mute output of the tele-
Blade contact A6 not connected:
no radio illumination when the radio is phone/CB radio to earth!
switched off.
A5 +12 V switching voltage output
(max. 0.5 A)
on bladec contact A 5 when the radio is
switched on.
For automatic aerial (extend/retract),
aerial amplifier (operating voltage) etc.
Waiting periods
To prevent deactivation of the coding being
possible by trial and error, waiting periods are
required between attempts. During these wait-
ing periods the car radio can be switched on
button.
and off but will not play.
- - - -"
E
During the waiting period
the car radio needs not be switched on, but it
must be connected to the permanent plus ter-
" "
1 – 4
minal. As long as the display indicates "SAFE",
the waiting period has not yet elapsed.
The waiting period is over when the number
of the next attempt is visible in the display,
Display:
e.g. "2 - - - -".
>1 - - -<
The table shows
the waiting
periods between the individual attempts.
Waiting period after the 7th attempt is always
24hrs!
After the 6th attempt we recommend having a
dealer complete the "Return to operation" or
"Deactivate coding" process.
button. The

Installation and Removal

Loudspeakers
+
Blade contacts B: Figure
Maximum output power
with 4 Ω loudspeakers: 4 x 7 W
í
Do not electrically connect speaker
connections to each other and do not
connect to chassis!
Front speakers Rear speakers
B3 right-hand + B1 right-hand +
B4 right-hand – B2 right-hand –
B5 left-hand + B7 left-hand +
B6 left-hand – B8 left-hand –
Return to operation Deactivating coding
The car radio is electronically disabled after it e.g., before removing the car radio:
has been disconnected from the car battery
1. The expert mode must be switched on and
(or permanent plus, terminal 30), e.g. after
"SAFE" visible in the display.
the radio has been removed during servicing.
Activate the setting.
1. Switch the car radio on:
"
LOUD
Briefly press the
EXPERT
The display indicates "SAFE".
The display indicates "
After approx. seconds, it will indicate
"I - - - -". 2. Enter the code number (on Identity Card),
as described in the chapter "Activating
2. Enter the code number (on Identity Card),
coding".
as described in the chapter "Activating
coding". 3. Confirm the code number:
"
LOUD
Briefly press the
EXPERT
3. Confirm the code number:
indicates briefly "CODE".
"
LOUD
Briefly press the button. The display
EXPERT
After approx. 3 seconds the radio will play.
indicates briefly "SAFE".
Coding is deactivated!
After approx. 3 seconds the radio will play.
Entry of incorrect code number:
Entry of incorrect code number:
"SAFE" remains in the display and the radio
"SAFE" remains in the display and the radio
does not play.
does not play.
Begin again.
Begin again.
Be sure to observe the waiting periods
Be sure to observe the waiting periods
between attempts.
between attempts.
Line output
Aerial
Connection for booster or active speaker.
The car radio is designed for aerials with an
C11 Rear speaker, left +
impedance of 75Ω to 150Ω. Extended aerial
C12 Rear speaker, right +
cables, e.g. for aerials at the rear of the car,
C13 Earth –
may impair reception.
C14 Front loudspeaker, left +
p ü
C15 Front loudspeaker, right +
Figures and
p C16 Switching voltage for booster on/off
– If necessary, use the aerial adapter (fig. ).
(max. 0.3 A).
p
– Fix the aerial adapter (fig. ) or aerial cable
ü
The entire current consumption of C17, C6
(fig. ) in the plastic holder.
and A5 is not allowed to exceed 0.5 A.
Additional connections
+
Blade contacts C: Figure
Connection for CD changer or AUX unit
C13 CD bus control line. For AUX mode,
connect it with C15.
C15 CD bus, earth.
C16 +12 V supply voltage for CD changer.
C17 Switching voltage for CD changer.
C18 CD-audio earth or AUX-audio earth.
C19 CD-audio left or AUX-audio left.
C20 CD-audio right or AUX-audio rigth.
C07 do not use, only for service.
C08 do not use, only for service.
Installation and removal
Coding
o a
The figures – can be found at the
beginning of this booklet.
Installation materials and accessories
Your dealer can advise you as to what installa-
button.
1 - - - -" tion materials you will need and what acces-
E
sories are available.
Inserting the mounting frame
o
Figure
button. The display
– Insert mounting frame b into cutout a of the
vehicle.
– Bend the tabs c behind cutout a as required
(depending on type of vehicle).
With cars of the VW/Audi company, from
1991 models on: make sure not to connect
the contact blade A7 with the S contact
(supply plug PIN 4 – brown/red cable) of
the car.
Installation and Removal
Inserting the car radio
o
Figure
– Insert the car radio all the way into the
installed mounting frame b.
The car radio should snap into place.
Removing the car radio
a
Figure
– Remove the control panel (page 4).
Insert both removal handles d as far as pos-
sible into the openings in the trim.
– Press both removal handles outward
and slowly pull the radio out.
Fuse T 5 A
+
Figure
Blade-type fuse T 5 A/ DIN 72 581– plugged.