Operation; Specifications - Monacor SA-50 Bedienungsanleitung

4 Setting Up and
Connecting the Amplifier
When setting up the amplifier, always provide free
air circulation through all air vents to ensure suf-
ficient cooling .
Always switch off the amplifier before making or
changing any connections .
4.1 Audio sources
The inputs PC, CD and AUX (10) allow to connect
three audio sources with line signal level (e . g . CD
player, tuner or audio output of a PC, mixer or DVD
player) . Connection is made via RCA jacks, for the
left (L) and right (R) channels respectively .
It is possible to connect another signal source
with line level via the 3 .5 mm jack PLAYER (2) on the
front panel . The jack can also be used for signals
with lower level, e . g . from the headphone output
of an MP3 player . To select the level, use the selec-
tor switch SOURCE (3) [
4.2 Speakers
Connect speakers with an impedance of 4 to 8 Ω
to the spring terminals (11) [LEFT = left speaker,
RIGHT = right speaker; observe the correct polarity
/ ] . When several speakers are interconnected at
an output, the total impedance of the speakers at
each output must not fall below 4 Ω .
4.3 Headphones
Use the 6 .3 mm jack PHONES (1) to connect ste-
reo headphones . In this case, the speakers will be
muted .
4.4 Power supply
Finally connect the mains cable (9) to a socket
(230 V/ 50 Hz) .

5 Operation

1) Prior to initial operation, set the control VOLUME
(4) to "0" .
2) Switch on the amplifier with the switch POWER
(7) . The power LED (8) lights up .
3) Switch on the audio source used, then select it
with the switch SOURCE (3) . When the audio
source has been connected to the input PLAYER
(2), select "HI IMP" for signal outputs with line
level or "LO IMP" for signal outputs with lower
level .
All rights reserved by MONACOR
reproduced in any form or by any means for any commercial use.
☞
chapter 5] .
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
®
4) Adjust the desired volume with the control
VOLUME . Adjust the sound as desired with the
controls BASS (5) and TREBLE (6) .
CAUTION Never adjust the audio system to
a very high volume . Permanent
high volumes may damage your
hearing! Your ear will get accus-
tomed to high volumes which donot seem to
be that high after some time . Therefore, do not
further increase a high volume after getting
used to it .
5) After operation, switch off the amplifier with
the switch POWER .

6 Specifications

RMS output power
at 4 Ω: � � � � � � � � � � � � � � � � � 2 × 12�5 W
at 8 Ω: � � � � � � � � � � � � � � � � � 2 × 10 W
Max� output power: � � � � � � � � � 2 × 25 W
Frequency range: � � � � � � � � � � � 20 – 20 000 Hz
S / N ratio: � � � � � � � � � � � � � � � � > 65 dB
Headphone output
Connection: � � � � � � � � � � � � � 6�3 mm jack
min� load impedance: � � � � � � 32 Ω
Inputs (sensitivity, impedance, connection)
PC, CD, AUX: � � � � � � � � � � � � 115 mV, 12 kΩ, RCA
PLAYER: � � � � � � � � � � � � � � � � "HI IMP" 115 mV, 12 kΩ
Tone control
Low frequencies (BASS): � � � � 100 Hz, ±12 dB
High frequencies (TREBLE): � � 12 kHz, ±12 dB
Power supply: � � � � � � � � � � � � � 230 V/ 50 Hz
Power consumption: � � � � � � � � 50 VA max�
Ambient temperature: � � � � � � � 0 – 40 °C
Dimensions (W × H × D): � � � � 212 × 56 × 200 mm
Weight: � � � � � � � � � � � � � � � � � � 1�9 kg
Subject to technical modification .
"LO IMP" 20 mV, 32 kΩ,
3�5 mm jack
7