Operation; Specifications - Monacor SA-100 Bedienungsanleitung

4 Setting Up and
Connecting the Amplifier
When setting up the amplifier, always provide free
air circulation through all air vents to ensure suffi-
cient cooling.
Always switch off the amplifier before making or
changing any connections.
4.1 Audio sources
The inputs PC, CD and AUX (11) allow to connect
three audio sources with line signal level (e. g. CD
player, tuner or audio output of a PC, mixer or DVD
player). Connection is made via RCA jacks, for the
left (L) and right (R) channels respectively.
It is possible to connect another signal source
with line level via the 3.5 mm jack PLAYER (3) on
the front panel. The jack can also be used for sig-
nals with lower level, e. g. from the headphone out-
put of an MP3 player. To select the level, use the
selector switch SOURCE (4) [
4.2 Speakers
Connect speakers with an impedance of 4 to 8 Ω to
the spring terminals (12) [LEFT = left speaker,
RIGHT = right speaker; observe the correct polarity
⊕/⊖]. When several speakers are interconnected
at an output, the total impedance of the speakers at
each output must not fall below 4 Ω.
4.3 Headphones
Use the 6.3 mm jack PHONES (1) to connect
stereo headphones. In this case, the speakers will
be muted.
4.4 Connector "USB CHARGE"
Use the connector USB CHARGE (2) to connect a
mobile device (e. g. MP3 player) which allows to be
supplied with power or allows its batteries to be
recharged via USB port. It is supplied with power
from the amplifier (500 mA max.). Thus, an addi-
tional power supply unit is not required.
4.5 Power supply
Finally connect the mains cable (10) to a socket
(230 V~ / 50 Hz).

5 Operation

1) Prior to initial operation, set the control VOL-
UME (5) to "0".
2) Switch on the amplifier with the switch POWER
(8). The power LED (9) lights up.
All rights reserved by MONACOR
may be reproduced in any form or by any means for any commercial use.
chapter 5].
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual
®
3) Switch on the audio source used, then select it
with the switch SOURCE (4). When the audio
source has been connected to the input
PLAYER (3), select "HI IMP" for signal outputs
with line level or "LO IMP" for signal outputs with
lower level.
4) Adjust the desired volume with the control VOL-
UME. Adjust the sound as desired with the con-
trols BASS (6) and TREBLE (7).
CAUTION Never adjust the audio system to
a very high volume. Permanent
high volumes may damage your
hearing! Your ear will get accus-
tomed to high volumes which do
not seem to be that high after some time.
Therefore, do not further increase a high vol-
ume after getting used to it.
5) After operation, switch off the amplifier with the
switch POWER.

6 Specifications

RMS output power
at 4 Ω: . . . . . . . . . . . . . 2 × 25 W
at 8 Ω: . . . . . . . . . . . . . 2 × 20 W
Max. output power: . . . . . 2 × 50 W
Frequency range: . . . . . . 20 – 20 000 Hz
S/N ratio: . . . . . . . . . . . . > 70 dB
Headphone output
Connection: . . . . . . . . 6.3 mm jack
min. load impedance: . 32 Ω
Inputs (sensitivity, impedance, connection)
PC, CD, AUX: . . . . . . . 140 mV, 46 kΩ, RCA
PLAYER: . . . . . . . . . . . "HI IMP" 140 mV, 12 kΩ
Tone control
Low frequencies
(BASS): . . . . . . . . . . . 100 Hz, ±12 dB
High frequencies
(TREBLE): . . . . . . . . . 12 kHz, ±12 dB
USB connector: . . . . . . . type A, 5 V/ 500 mA max.
Power supply: . . . . . . . . . 230 V~ / 50 Hz
Power consumption: . . . . 150 VA max.
Ambient temperature: . . . 0 – 40 °C
Dimensions (W × H × D): . 212 × 56 × 250 mm
Weight: . . . . . . . . . . . . . . 2.6 kg
Subject to technical modification.
"LO IMP" 25 mV, 32 kΩ,
3.5 mm jack
GB
7