NovoPress ACO403 Betriebsanleitung Seite 25

Pos : 37 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Kapitel übeers chrift+Ü berschrift - T abelle @ 0\mod_1385652188500_18.doc x @ 1618 @ 2 @ 1
8.1 Meaning of the LED display
LED display
Pos : 38 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED _l euc htet @ 0\mod_1400057953215_18.doc x @ 2330 @ @ 1
Green LED (2) lights up.
Pos : 39 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED _aus @ 0\mod_1400062238490_18.doc x @ 2344 @ @ 1
Green LED (2) off
(pressing operation in
progress).
Pos : 40 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED _blinkt @ 0\mod_1400062218616_18.doc x @ 2337 @ @ 1
Green LED (2) flashes.
Pos : 41 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Bl aue_LED_blinkt @ 3\mod_1491998145093_18.doc x @ 29107 @ @ 1
Blue LED (10) flashes.
Pos : 42 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Bl aue_LED_l euchtet @ 3\mod_1492000411326_18.doc x @ 29128 @ @ 1
Blue LED (10) lights up.
Pos : 43 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/r ote_LED_blinkt @ 3\mod_1489564282895_18.doc x @ 28653 @ @ 1
Red LED (3) flashes.
Pos : 44 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/R ote_LED _leuchtet @ 0\mod_1400062249067_18.doc x @ 2358 @ @ 1
Red LED (3) lights up.
Pos : 45 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/ R ote-und_Gr üne_LED _bli nken_abwechsel nd- ACO401 @ 4\mod_1501837221719_18.doc x @ 31615 @ @ 1
Red (3) and green (2)
LED flash alternately.
Pos : 46 /RVT/Inbetri ebnahme und Betrieb/Ausg angsl age Press- Sc hlinge/01- Ü bersc hrift- Ausg angsl age Press- Sc hlinge - AC O401 @ 3\mod_1490788635012_18.doc x @ 28823 @ 2 @ 1
8.2 Starting position of the press collar (Fig. 5)
Pos : 47 /RVT/Inbetri ebnahme und Betrieb/Ausg angsl age Press- Sc hlinge/02- Info-Gl eits egmente - AC O401 @ 3\mod_1490788774826_18.doc x @ 28848 @ @ 1
Information!
To ensure that the press collars function correctly, the sliding segments must be free to
move.
The sliding segments are always pressed back automatically into the correct starting
position by springs.
Therefore:
–
–
Pos : 48 /RVT/Inbetri ebnahme und Betrieb/Ausg angsl age Press- Sc hlinge/03- Oval e F orm - AC O401 @ 3\mod_1490788901842_18.doc x @ 28873 @ @ 1
The press collar must be positioned in the way shown (oval shape) before it is placed on a fitting. After
the press collar has been opened and removed from a fitting, the press collar must again be
positioned in the way shown.
Pos : 49 /RVT/Inbetri ebnahme und Betrieb/Schli eßen und Öffnen Schli nge/01- Sc hließ en und Öffnen AC O403 @ 4\mod_1511962283677_18.doc x @ 33239 @ 22 @ 1
Status/cause
On standby.
Automatic press cycle is on,
device ends the pressing
operation automatically.
Insufficient battery charge.
The press device is ready
for connection.
The press device is
connected with the
NovoCheck app.
Device not within the
temperature range
Device fault.
Service interval reached.
Ensure that marking lines (M) on shells (C) are aligned with the edges of the sliding
segments (D) when the press collar is in starting position. (Fig. 5)
If this is not the case, have the press collars repaired.
Measure
Charge or replace battery.
The press device can be connected with
the NovoCheck app.
The device only works within a
temperature range of -10 to +50°C. If the
red LED is flashing, the device must be
moved into a warmer or colder area. The
device can be warmed to operating
temperature by means of dry runs.
If the device is too warm it must be cooled
down by means of a short break.
Press the start button (1). If this is
unsuccessful, the press device is
defective.
Send the device to a specialist workshop.
NOTE!
The pressing operation may not have
been completed; please check and repeat
if required.
Take the press device to be serviced
within the next 100 pressing operations.
21
ACO403
EN