Inhaltsverzeichnis
Werbung
6. When the charger is not in use it should not be
plugged in. When unplugging, do not pull the plug out
by the cable.
7. If the charger breaks down or suffers from other
technical problems, take it to a recognised dealership
to be checked before using it again. Any damaged
parts must be replaced.
8. Take care when handling the battery pack, do not
drop it or knock it against other things.
9. Never attempt to repair the battery charger or
battery pack yourself; this can be extremely
dangerous. Repairs should always be carried out by a
recognised dealership.
10. Always unplug the charger before cleaning or
carrying out any other maintenance on it.
11. Do not attempt to charge the battery pack in
temperatures of below 10 degrees or above 40
degrees centigrade.
12. The air vents on the battery charger must be kept
unblocked.
13. The battery pack must not be short-circuited.
When an apparatus short-circuits, the strength of
the electric current is increased. This can cause the
apparatus to over heat, catch fire or even explode, causing
damage and also endangering the operator.
To avoid this;
1. Firstly do not connect any wires to the terminals of the
battery pack;
2. Ensure that no metal objects (nails, coins, paper-clips)
are caught in the opening of the battery pack;
3. Do not expose the battery pack to water or rain.
14. If the battery pack is broken or can no longer be re-
charged it must be properly disposed of.
15. Never throw the battery pack into water or a fire – it
may explode.
GENERAL USE
•
This pump is NOT designed for continuous
operation e.g. as a swimming pool or pond
circulation pump.
•
Ensure there are no obstructions around the inlet
openings around the base of the pump. The inlet
openings must be clear of mud or sludge at the
bottom of a pool.
•
After use allow the pump to run using clean water for
2 - 3 minutes in order to remove residues and
particles that may have accumulated in the pump and
outlet hose.
Use only for pumping clean water.
Running dry will destroy the pump. Immediately
stop the pump when there's no water left to pump
(push the switch).
4
Note: If the level of water becomes to low, any sludge in
the shaft will dry out more quickly and this may prevent
the pump from restarting. To ensure the pump works
efficiently the bottom of the shaft must be kept free of
sludge as far as possible and cleaned on a regular basis
when not in use.
BLOCKAGES
If you suspect the pump has become blocked, remove
the battery out of the pump:
•
Examine the hose and base plate.
•
Check if there's a kink in the hose.
•
Clean the hose and water inlet.
OPERATING INSTRUCTIONS
Warning! Do not throw the pump into deep water.
Maximum water level is ± 6 cm. The water level
has to stay below the switch!
Fig. 1
•
Push the on/off switch to start the machine (1).
•
Push the on/off switch to stop the machine.
CHARGING
Fig. 2
•
Remove the battery from the machine
•
Position the battery in the battery charger as
indicated in the illustration.
•
Plug the mains adapter into the (wall) socket
•
The charging process starts; the red LED is now on
•
As soon as the green LED is on, charging has finished
and the battery is ready for use
STORAGE
When storing the machine for longer than 6 weeks:
•
Fully discharge the battery (by running the product)
and then recharge the battery for 3-5 hours.
•
Store in a dry and frost-free place.
•
Recharge the battery every 1 or 2 months during the
winter, because the battery will discharge slowly.
SERVICE & MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
These machines have been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper machine care and regular cleaning.
CLEANING
Keep the ventilation slots of the machine clean to prevent
overheating of the engine. Regularly clean the machine
housing with a soft cloth, preferably after each use. Keep
the ventilation slots free from dust and dirt. If the dirt does
not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia
water, etc. These solvents may damage the plastic parts.
LUBRICATION
The machine requires no additional lubrication.
.
.
.
NiCd
Ferm
.
ı
CE
EN 60745-1, EN 60335-2-4, EN 60335-2-29,
EN 55014-2, EN 55014-2, EN 61000-3-2,
EN 61000-3-3
98/37/EEC, 73/23/EEC, 89/336/EEC
01-11-2004
ZWOLLE NL
W. Kamphof
.
Ferm BV, Zwolle,
Ferm
Ferm
,
.
,
Ferm.
.
.
,
.
( GR )
,
.
.
,
49
Werbung
Inhaltsverzeichnis
