Specifications; Safety Instructions - Makita 2414NB Betriebsanleitung

ENGLISH
1 Safety guide
2 Shaft lock
3 Socket wrench
4 Cut-off wheel
5 Inner flange
6 O-ring
7 Spindle
8 Ring
9 Outer flange
10 Hex bolt
11 Screw
12 Spark guard

SPECIFICATIONS

Model
Wheel diameter .................................................................................................................................................. 355 mm
Hole diameter .................................................................................................................................................... 25.4 mm
–1
No load speed (min ) ............................................................................................................................................ 3,800
Dimensions (L x W x H)
With under cover..............................................................................................................500 mm x 280 mm x 620 mm
Without under cover.........................................................................................................500 mm x 280 mm x 600 mm
Net weight
For tools with European type safety guide and under cover.............................................................................. 18.5 kg
For tools with European type safety guide and without under cover ................................................................. 17.8 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for cutting in masonry and ferrous
materials with appropriate abrasive cut-off wheel.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety pre-
cautions should always be followed to reduce the
risk of fire, electric shock and personal injury, includ-
ing the following. Read all these instructions before
attempting to operate this product and save these
instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use power
tools in damp or wet locations. Keep work area well
lit. Don't use power tools in presence of flammable
liquids or gases.
3. Guard against electric shock
Prevent body contact with grounded surfaces (e.g.
pipes, radiators, ranges, refrigerators).
Explanation of general view
13 Stopper plate
14 Guide plate
15 Hex bolts
16 Vise plate
17 Vise nut
18 Vise handle
19 Spacer block
20 Straight piece of wood
(Spacer)
21 Over 190 mm long
22 Over 45 mm wide
23 Over 65 mm wide
4.
5.
6.
7.
8.
9.
10. Connect dust extraction equipment
11. Don't abuse cord
12. Secure work
13. Don't overreach
24 Diameter of workpiece
25 Spacer block
26 Vise
27 Width of spacer block
28 Blocks
29 Switch trigger
30 Lock button/Lock-off button
31 Wing bolt
32 Under cover
33 Limit mark
34 Screwdriver
35 Brush holder cap
Keep children away
Do not let visitors contact tool or extension cord. All
visitors should be kept away from work area.
Store idle tools
When not in use, tools should be stored in dry, high,
or locked-up place, out of the reach of children.
Don't force tool
It will do the job better and safer at the rate for which
it was intended.
Use right tool
Don't force small tools or attachments to do the job
of a heavy duty tool. Don't use tools for purposes not
intended; for example, don't use circular saw for cut-
ting tree limbs or logs.
Dress properly
Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and non-skid
footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and sharp
edges.
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to operate
tool.
Keep proper footing and balance at all times.
2414NB
5