Working Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GMB 32 Professional Originalbetriebsanleitung

OBJ_BUCH-1761-002.book Page 11 Friday, June 13, 2014 8:07 AM
Restarting Protection
The restarting protection prevents uncontrolled starting of
the drill after the power supply is interrupted.
For restarting the operation, press the motor On/Off switch
6 to position "I".
Note: Resumption of the power supply.

Working Advice

 For drilling, observe the operating instructions of your
drill.
 The magnet holding force of the drill stand mainly de-
pends on the thickness of the workpiece. The thickness
of the material should not be less than 8 mm.
 When drilling overhead or on surfaces that are not hor-
izontal, secure the drill stand with a safety chain. In
case of a power failure or excessive load, the holding force
of the magnet is not maintained. The drill stand can fall
down and cause accidents.
Centre-punch metal workpieces.
Rotate the drilling lever 1 to apply feed of the drill.

Maintenance and Service

Maintenance and Cleaning

Use the supplied Hex key 14 to adjust the guide rail (see figure
B). Use the supplied open-end spanner 13 to loosen the lock
nuts 11. Tighten the set screws 12 evenly using the supplied
Hex key 14 and retighten the lock nuts 11.
Keep the drill stand clean at all times for good working results
and safe working.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the drill stand.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0844) 7360109
E-Mail: boschservicecentre@bosch.com
Bosch Power Tools
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
E-Mail: bsc@zsd.co.za
Bosch Headquarters
Midrand, Gauteng
Tel.: (011) 6519600
Fax: (011) 6519880
E-Mail: rbsa-hq.pts@za.bosch.com
English | 11
1 609 92A 0KN | (13.6.14)