Technical Data - Bosch GMB 32 Professional Originalbetriebsanleitung

OBJ_BUCH-1761-002.book Page 10 Friday, June 13, 2014 8:07 AM
10 | English
Product Features
The numbering of the product features refers to the illustra-
tion of the drill stand on the graphics pages.
1 Drilling lever with drilling-depth scale
2 Screw for the side holder
3 Side holder for drill
4 Drill fixture
5 Screw for drill fixture
6 Motor On/Off switch
7 Socket outlet for drill
8 Magnet On/Off switch
9 Insulated gripping surfaces
10 Safety chain
11 Lock nut
12 Set screw for adjustment of the guide rail
13 Open-end spanner
14 Hex key
A complete overview of accessories can be found in our accesso-
ries program.

Technical Data

Magnetic drill stand
Article number
Rated power input
Holding force of the magnet
Max. drilling dia.
(GBM 32-4, MK3 tool holder)
– Twist drill bit
– Core bit
Drill stroke, max.
Diameter of drill fixture
Weight according to
EPTA-Procedure 01/2003
Protection class
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: –.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
19.05.2014
1 609 92A 0KN | (13.6.14)
Assembly
Inserting the Drill
Remove the auxiliary handle from your drill, if required (see
the operating instructions of the drill).
Loosen screw 5 using an Hex key. Insert the drill with the drill
collar from above into the drill fixture 4 to the stop. Mount
screw 2 in order to connect the drill with the side holder 3.
Hand-tighten screw 5 using an Hex key.
 Check the tight seating of the drill in the drill fixture.
When the drill is not securely fastened, serious injury may
result.
Mounting the Safety Chain (see figure A)
For all work being performed in inclined, vertical or overhead
positions, secure the drill stand against falling down with the
provided safety chain 10.
 Before using the safety chain, check its proper func-
tion. Never use a damaged safety chain; replace a dam-
aged safety chain immediately.
Fasten the safety chain in such a manner that the drill stand
moves away from you, should it come undone.
Fasten the safety chain around the carrying handle of the drill
GMB 32
stand with as little play as possible.
0 601 193 0..
Operation
W 95
kN 25
 Pull the plug from the socket outlet and/or remove the
battery before carrying out adjustments on the power
tool or replacing accessory parts. Unintentional starting
of drills is the cause of some accidents.
mm 32
 After each adjustment on the drill stand, retighten the
mm 12 – 60
bolts and locking handles.
mm 223
mm 65
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
kg 26
er source must agree with the voltage specified on the
/I nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
 Insert the mains plug of the drill only into socket outlet
7. Switch the drill on and lock the On/Off switch of the
drill with the lock-on button. Otherwise, the drill cannot
be switched on or off via the motor On/Off switch 6 on the
drill stand.
Push the magnet On/Off switch 8 upward and check if the drill
stand adheres to the workpiece surface.
To start the drill, press the motor On/Off switch 6 to position
"I".
Note: The drill can only be started when the magnet has al-
ready been switched on.
To switch off the drill, press the motor On/Off switch 6 to po-
sition "0".
Wait until the drill has come to a complete stop before push-
ing the magnet On/Off switch 8 downward in order to switch
the magnet off.
When not using the drill, switch it off in order to save energy.
Bosch Power Tools