Hitachi NP 14DSL Bedienungsanleitung Seite 14

English
14. Take care when nailing thin boards or the corners of
wood.
When nailing thin boards, the nails may pass right
through, as may also be the case when nailing the
corners of wood due to deviation of the nails. In such
cases, always make sure that there is no one (and
nobody's hands or feet; etc.) behind the thin board or
next to the wood you are going to nail.
15. Simultaneous nailing on both sides of the same wall
is dangerous.
Under no circumstances should nailing be performed
on both sides of a wall at the same time. This would
be very dangerous since the nails might pass through
the wall and thus cause injuries.
16. Do not use the power tool on scaffoldings, ladders.
The power tool shall not be used for specific
application for example:
– when changing one driving location to another
involves the use of scaffoldings, stairs, ladders or
ladder alike constructions, e.g. roof laths,
– closing boxes or crates,
– fitting transportation safety systems e.g. on
vehicles and wagons
17. Do not disconnect the battery with your finger on
the trigger.
If you disconnect the battery with your finger on the
trigger, the next time the battery is connected, there
is a danger that the power tool will fire a nail
spontaneously, or operate incorrectly.
18. Disconnect the battery and take out any nails left in
the magazine after use.
Disconnect tool from battery before doing tool
maintenance, cleaning a jammed fastener, leaving work
area, moving tool to another location, or after use. It is
very dangerous for a nail to be fired by mistake.
19. When removing a nail which has become stuck, make
sure to first of all disconnect the battery.
When removing a nail which has become stuck in the
nail outlet, first of all make sure to disconnect the
battery.
Accidental firing of the nail could be very dangerous.
20. When attaching and detaching the nose cap,
disconnect the battery.
When attaching the accessory nose cap to the tip
of the push lever and when detaching it, make sure
to disconnect the battery beforehand. It is very
dangerous for a nail to be fired by mistake.
21. Always assume that the tool contains fasteners.
Careless handling of the pin nailer can result in
unexpected firing of fasteners and personal injury.
22. Do not point the tool towards yourself or anyone
nearby.
Unexpected triggering will discharge the fastener
causing an injury.
23. Do not actuate the tool unless the tool is placed
firmly against the workpiece.
If the tool is not contact with the workpiece, the
fastener may be deflected away from your target.
24. Disconnect the tool from the power source when the
fastener jams in the tool.
While removing a jammed fastener, the pin nailer
may be accidentally activated if it is plugged in.
25. Use caution while removing a jammed fastener.
The mechanism may be under compression and the
fastener may be forcefully discharged while
attempting to free a jammed condition.
13
26. Do not use this pin nailer for fastening electrical
cables.
It is not designed for electric cable installation and
may damage the insulation of electric cables thereby
causing electric shock or fire hazards.
27. Always charge the battery at a temperature of 0 –
40°C.
A temperature of less than 0°C will result in over
charging which is dangerous. The battery cannot be
charged at a temperature greater than 40°C.
The most suitable temperature for charging is that of
20 – 25°C.
28. Do not use the charger continuously.
When one charging is completed, leave the charger
for about 15 minutes before the next charging of
battery.
29. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
30. Never disassemble the rechargeable battery and
charger.
31. Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great electric
current and overheat. It results in burn or damage to
the battery.
32. Do not dispose of the battery in fire.
If the battery burnt, it may explode.
33. Do not insert object into the air ventilation slots of
the charger.
Inserting metal objects or inflammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
34. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery life
becomes too short for practical use. Do not dispose
of the exhausted battery.
35. Using an exhausted battery will damage the charger.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips
with the protection function to stop the output.
In the cases of 1 to 3 described below, when using
this product, even if you are pulling the switch, the
motor may stop. This is not the trouble but the result
of protection function.
1. When the battery power remaining runs out, the
motor stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes
of overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand,
please be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
During work make sure that swarf and dust do not
fall on the battery.
Make sure that any swarf and dust falling on the
power tool during work do not collect on the battery.