Hitachi NP 14DSL Bedienungsanleitung Seite 18

English
Do not load nails of different lengths at the same
time.
Do not load multiple strips of few nails at one time.
Doing so may lead to jamming or other malfunctions.
Nails from 15 to 45 mm can be used with this power
tool.
Place the tips of the nails of whatever length against
the bottom of the groove in the magazine. (Fig. 12)
(1) Lightly press the stop lever.
(2) Slowly pull out the magazine cover. (Fig. 13)
(3) Push the nails against the uneven surface of the
magazine and insert the nail tips as far as they will go
into the groove of the magazine.
(4) Push the nails in the magazine into the blade guide
with your fingers. (Fig. 14)
(5) Push the magazine cover forward to return it to the
closed position, checking that the nails do not stick
out above the uneven surface of the magazine.
NOTE
Close the magazine cover gently.
Applying excessive force may result in deformation
of the nail strip, preventing the magazine cover from
closing.
If the magazine cover is hard to close, check the
groove of the magazine.
Nails sometimes get into the groove. If this happens,
tilt the power tool and remove the nails with a
precision screwdriver or thin bar. In particular, if any
nails get into the hole shown in the cross-section
drawing, remove them through the window in the
back of the magazine. (Fig. 15)
5. How to Remove Nails
(1) Press the stop lever and pull out the magazine cover.
(2) Remove the nails from the blade guide or magazine.
NOTE
If the strip breaks inside the blade guide, nails may
be left behind when the nails at the front are removed.
Check carefully inside the blade guide, as it will be
hard to see any nails that have been left behind there.
If nails get jammed and cannot be removed, refer to
the section "Removing Nail Jams."
6. Anti Blank Firing Mechanism
This nailer is equipped with an anti blank firing
mechanism to prevent blank firing when the nails
run out.
The trigger will cease to operate when 11 or fewer
nails remain.
Approximately 11 nails will remain after firing the
strip of nails, but replenishing the magazine with nails
of the same length will enable nailing to be continued.
<Inspection procedures for switch arm operation (Fig. 16)>
(1) To prevent accidents due to incorrect operation, be
sure to disconnect the battery.
(2) Open the magazine cover and remove all the
remaining pin nails.
(3) Close the magazine cover gradually and check that
the switch arm moves slightly approximately 1 cm
before becoming tightly shut.
(4) If the switch arm does not move, check for dirt or
foreign objects around it. In addition, apply a drop of
machine oil to the rotating part to facilitate movement.
(5) Lastly, fill the magazine with strips of 11 or more pin
nails and check that the switch arm does not move
when the magazine is closed.
17
7. About Remaining Battery Indicator
When pressing the remaining battery indicator switch,
the remaining battery indicator lamp lights and the
battery remaining power can be checked. (Fig.5) When
releasing your finger from the remaining battery
indicator switch, the remaining battery indicator lamp
goes off. The table 4 shows the state of remaining
battery indicator lamp and the battery remaining
power.
Table 4
State of lamp Battery Remaining Power
The battery remaining power
is enough.
The battery remaining power
is a half.
The battery remaining power
is nearly empty.
Re-charge the battery soonest possible.
As the remaining battery indicator shows somewhat
differently depending on ambient temperature and
battery characteristics, read it as a reference.
NOTE
Do not give a strong shock to the switch panel or
break it.It may lead to a trouble.
To save the battery power consumption, the
remaining battery indicator lamp lights while pressing
the remaining battery indicator switch.
8. How to use the LED light
Every time you press the light switch on the switch
panel, the LED light lights or goes off. (Fig. 6)
To prevent the battery power consumption, turn off
the LED light frequently.
CAUTION
Do not expose directly your eye to the light by looking
into the light.
If your eye is continuously exposed to the light, your
eye will be hurt.
NOTE
To prevent the battery power consumption caused
by forgetting to turn off the LED light, the light goes
off automatically in about 15 minutes.
9. Using the hook
The hook is used to hang up the power tool to your
waist belt while working.
CAUTION
When using the hook, hang up the power tool firmly
not to drop accidentally.
If the power tool is dropped, it may lead to an accident.
Make sure the trigger has been locked and the battery
removed when using the hook.
Install securely the hook. Unless the hook is securely
installed, it may cause an injury while using.
(1) Removing the hook.
Remove the screws fixing the hook with Philips screw
driver. (Fig. 7)
(2) Replacing the hook and tightening the screws.
Install securely the hook in the groove of power tool
and tighten the screws to fix the hook firmly. (Fig. 8)