Maintenance; Residual Risks - Ryobi RHT36C60R15 Originalanleitung

the blade cuts at top speed, which allows quick and
precise trimming. This speed is best for the regular
maintenance of your hedges.
●
Setting 2 ( hi-torque) - Use this setting to cut thick or
dense hedges. The hi-torque setting provides more
cutting power to trim larger branches. This setting is
not intended for everyday trimming.
Use the speed switch to change the cutting speed to
your desired setting.
WARNING
If the product is dropped, suffers heavy impact, or begins
to vibrate abnormally, immediately stop the product and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service centre.
TRANSPORTATION AND STORAGE
■
Stop the product, remove the battery, and allow both to
cool before storing or transporting.
■
Clean all foreign material from the product. Store it in a
cool, dry, and well-ventilated place that is inaccessible
to children. For extra safety, store the battery separately
from the hedge trimmer. Keep away from corrosive
agents such as garden chemicals and de-icing salts.
Do not store outdoors.
■
Cover the blade with the blade protector before storing
the product, or during transportation.
■
For transportation, secure
movement or falling to prevent injury to persons or
damage to the product.
TRANSPORTING LITHIUM BATTERIES
Transport batteries in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, nonconductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.

MAINTENANCE

WARNING
Use only original manufacturer's replacement parts,
accessories and attachments. Failure to do so can
cause possible injury, poor performance and may void
your warranty.
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service, we suggest you bring the
product to your nearest authorised service centre for
repair. When servicing, use only identical replacement
parts.
The blades are extremely sharp. To prevent personal
injury, exercise extreme caution when cleaning,
lubricating, and fitting or removing the blade protector.
Remove the battery before adjustment, maintenance, or
cleaning.
■
■
■
the product against
■
■

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
■
■
■
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness, and blanching of the fi ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
WARNING
WARNING
You may make adjustments and repairs described
in this user manual. For other repairs, contact the
authorised service agent.
After each use, clean the body and handles of the
product with a soft dry cloth.
After each use, clean the debris from the blades
with a stiff brush, and then carefully apply a rust
preventative lubricant before refitting the blade
protector. The manufacturer recommends you to use a
rust preventative and lubricant spray to apply an even
distribution and reduce the risk of personal injury from
contact with the blades. For information about suitable
spray product, check with your local authorised service
centre.
You may lubricate the blades lightly before use if
necessary using the above method.
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
Injury caused by contact with the blades. Contact with
the blades can cause serious injury. Keep the blade
away from yourself and others. Cover it with the blade
protector whenever you are not cutting.
Injury caused by vibration. Always use the right tool for
the job. Use designated handles and restrict working
time and exposure.
Exposure to noise can cause hearing injury. Wear ear
protection and limit exposure
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
English | 3