Werbung
Verfügbare Sprachen
Verfügbare Sprachen
8. Checking and troubleshooting
8.1. Checking
1.
Connect the cables of the automobile battery.
2.
Switch the ignition ON, without starting the motor.
3.
Switch the monitor on. To do this, press the monitor's ON/OFF button.
4.
Activate the parking brake and engage the reverse gear.
5.
Wait until the monitor shows the view to the rear.
6.
If necessary, change the image orientation to get the proper view.
8.2. Troubleshooting
When I engage the reverse gear, all
•
That means there is no communication between
I see is snow.
camera and monitor.
•
What is the purpose of the blue
•
The blue wire is an extra wire that can be connected
wire on the monitor cable?
to another current source, preferably the cable of
the reversing light. It works as a trigger for switching
the monitor on when the vehicle is put into reverse
gear.
•
Why is the image on the screen
•
The image orientation can be changed as desired
upside down?
by pressing the Rotate button on the monitor long
enough.
•
Why do I see so much
•
Because it is a wireless device, other wireless
interference and rolling lines
devices can interfere with the signal between
when using the device?
monitor and camera. Mobile phones and other
devices with wireless technology can interfere with
the system.
•
When it is light outside, is it
•
Yes. The camera needs a while to normalise and
normal that the screen needs
stabilise itself when it is light outside. But if the
a while to show the actual
monitor needs more than 15 seconds to normalise
image?
itself and show the view to the rear, please contact
our technology team.
22
•
Check the connection of the camera at the
reversing light. Make sure that all cables are
securely attached.
•
Look up the information on the wiring of the
reversing lights in the operating instructions
of your vehicle. Make sure that the red wire of
the camera is connected to the positive cable
of the reversing light and the black wire of the
camera is connected to the ground cable of the
reversing light.
•
If you use Scotchlok® connectors, check
whether you have crimped the wires with a
gripper to make a secure connection.
•
Press the Rotate button until the desired image
orientation is found.
•
Turn off other wireless devices. Then the
interference will stop. To get a better signal, try
the following:
-
Move the monitor on the dashboard.
-
Move the antenna cable and put it in a place
with little interference.
9. Maintenance
Before cleaning the system (monitor), turn off all components connected to power, and disconnect them from the power source. If required, clean
the camera's lens. Do not use any abrasives or solvents! The system works maintenance-free. Check the technical status of the device,
e.g. whether enclosures or insulations are damaged, and whether the camera enclosure is still leak tight etc.
10. Disposal
In order to preserve, protect and improve the quality of environment, protect human health and utilise natural resources prudently and
rationally, the user should return unserviceable product to relevant facilities in accordance with statutory regulations. The crossed-out
wheeled bin indicates the product needs to be disposed separately and not as municipal waste.
11. Technical data
Camera
Operating voltage
12 V= (on-board power supply)
Frequency band
2.4 GHz band
LCD size
Operating temperature
-20°C to +60°C
Dimensions: (L x W x H)
66 x 60 x 72 mm
12. Declaration of conformity
Hereby, Conrad Electronic SE, Klaus-Conrad-Straße 1, 92240 Hirschau, declares that this product is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
The declaration of conformity to this product can be found at www.conrad.com.
LCD monitor
12 V= (on-board power supply)
2.4 GHz band
3.5"
-20°C to +60°C
110 x 82 x 27.5 mm
23
Werbung
Kapitel
Fehlerbehebung
