Specifications; Additional Safety Rules For Tool - Makita JR180D Betriebsanleitung

ENGLISH
1 Battery cartridge
2 Push button
3 Released position
4 Fixed position
5 Blade clamp sleeve

SPECIFICATIONS

Model
Length of stroke .................................................... 23 mm
Strokes per minute ........................................... 0 – 2,700
Cutting capacities
Pipe ................................................................... 90 mm
Wood ................................................................. 90 mm
Overall length ..................................................... 469 mm
Net weight (with battery cartridge) ........................ 3.5 kg
Rated voltage ................................................... D.C. 18 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for sawing wood, plastic and ferrous
materials.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
7. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
4
Explanation of general view
6 Blade
7 Lever
8 Shoe
9 Switch trigger
10 Lock-off button
8.
JR180D
9.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
2.
3.
4.

ADDITIONAL SAFETY RULES FOR TOOL

1.
2.
ENC004-1
3.
4.
5.
6.
7.
8.
9.
11 Press in
12 Limit mark
13 Screwdriver
14 Brush holder cap
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear protec-
tors and thickly padded gloves.
Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately.
Do not attempt to cut workpieces larger than
specified in this manual (especially hollow pipe).
The blade might snap and cause an injury.
(Fig. 1)
Hold the tool firmly.
Be sure no one is below when using the tool in
high locations.
Do not point the tool at anyone in the immediate
vicinity.
When making a "blind" cut (you can't see behind
what is being cut), be sure that hidden electrical
wiring or water pipes are not in the path of the
cut. If wires are present, they must be discon-
nected at their power source by a qualified per-
son or avoided to prevent the possibility of lethal
shock or fire. Always hold the tool ONLY by the
insulated gripping surfaces to prevent any elec-
tric shock if you accidentally cut through a "live"
wire. Water pipes in "blind" areas must be
drained and capped before cutting.
Be careful not to hit the end of the blade against
something during operation. Damage to the tool
or dangerous blade breakage may occur. (Fig. 2)