Installation - Conrad 75 23 40 Bedienungsanleitung

O P E R A T I N G I N S T R U C T I O N S
TFT Monitor 14.2 cm
Item-No. 75 23 40
Intended Use
The monitor features an AV input and a second video input. The product can be operated via the
keys on the monitor and an IR remote control included in the delivery. For the power supply, the
enclosed wall plug transformer can be used.
Any other use than that described above may damage the product. Moreover, this may give rise
to hazards such as short-circuiting, fire, electric shock, etc. No part of the product may be mod-
ified or converted!
The safety instructions must be observed at all times!
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Monitor
• IR remote control
• Wall plug transformer
• Bracket
• Connection cable
• Operating Instructions
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
We do not accept liability for damage to property or personal injury caused by
improper handling or non-compliance with the safety instructions! In such
cases the warranty will be null and void.
Dear customer,
these safety instructions are not only to protect the product but also for your own
safety and that of other people. Therefore, please read this chapter very carefully
before using the product for the first time!
• The unauthorised conversion and/or modification of the product is inadmissible
because of safety and approval reasons (CE). Do not open/disassemble! It does
not contain any internal parts that need to be adjusted or maintained by you.
• The product is not a toy and must be kept out of the reach of children. It should be
operated out of the reach of children.
• The design of the power adapter complies with protection class II. Only use a stan-
dard mains socket as the voltage source (see section "Technical data").
• The product is only intended for use in dry indoor rooms; it must not get damp or
wet; never touch it with wet hands!
Use of the wall plug transformer involves the risk of a potentially fatal electric shock!
Protect the product from direct sunlight, extreme heat (>35°C), cold (<0°C), dust
and dirt, vibrations or mechanical loads. Handle the product with care, it can be
damaged by impacts, blows or by falling from a low height.
• When the product is taken from a cold to a warm room (e.g. during transport), con-
densation may be produced.
Allow the product to reach room temperature before you connect it to the mains
voltage. This may take several hours. Otherwise, there is lethal danger due to an
electric shock!
• Do not pull the wall plug transformer from the mains socket by pulling on the cable.
• It can be assumed that safe operation is no longer possible if:
- the device is visibly damaged,
- the device no longer works
- the device has been stored under adverse conditions.
- it was exposed to heavy loads during transport
• If the wall plug transformer is damaged, do not touch it; there is danger to life from
electric shock!
First switch off the mains voltage at the mains socket to which the wall plug trans-
former is connected (e.g. switch off at the corresponding circuit breaker or remove
the fuse).
www.conrad.com
Version 04/11
°
General Battery Instructions
• Batteries should be kept out of the reach of children.
• Do not leave batteries lying around in the open; there is a risk of them being swallowed by chil-
dren or domestic animals. If swallowed, consult a doctor immediately.
• Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suitable
protective gloves.
• Batteries/rechargeable batteries must not be short-circuited, opened or thrown into a fire.
There is a risk of explosion!
• Do not recharge standard, non-rechargeable batteries, risk of explosion!
• Please pay attention to the correct polarity (plus/+ and minus/-) when inserting the battery.
• If the product is not to be used for a while (e.g. storage), remove the battery. Old batteries can
leak and damage the product.
Inserting Batteries into the IR Remote Control, Changing
Batteries
• To insert or replace the battery, remove the battery compartment on the lower edge of the IR
remote control. Then insert a battery, paying attention to the correct polarity.
• Push the battery compartment, with the battery, back into the IR remote control, until the bat-
tery compartment clicks into place.
• The battery needs replacing if the range of the IR remote control decreases or the monitor no
longer reacts to the IR remote control.

Installation

Fasten the bracket provided to the rear of the monitor. Using the bracket, the monitor can be
mounted on different surfaces; even installation underneath a shelf, or on the wall, is possible.
Connection
Connect the monitor socket to the enclosed connection cable. On the end of the monitor's con-
nection cable, the following connectors/sockets are to be found:
• Yellow RCA jack:
• White RCA jack:
• Red RCA jack:
• Low voltage socket:
Secure the cable e.g. with cable fasteners. Pay attention that the cable is protected from sharp
edges. Never bend the cable!
In order to be able to operate a surveillance camera with BNC connection on one of the two video
inputs, you will need a suitable adapter. The latter is available as accessory.
Connect the low voltage connector to the corresponding round plug on the wall plug transformer.
Afterwards, plug the wall plug transformer into a mains socket.
Only after doing this should the wall plug transformer be unplugged from the mains
socket. Dispose of the damaged wall plug transformer in an environmental-friendly
way, do not use it any more.
Replace it with a new wall plug transformer with the same specifications.
• Disconnect the power supply from the product, if it is not to be used for a while (e.g.
for storage).
• Do not leave packing materials unattended. They may become dangerous play-
things for children.
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Materials are
to be observed.
• In schools, educational centres, hobby and self-help workshops the operation of
the product is to be supervised by trained employees.
• If you have any questions that are not answered in this instruction manual, please
contact our technical support centre or consult a professional.
The battery might already be inserted in the IR remote control. If there is a small
plastic strip in the battery compartment, please remove it; it is used to protect the bat-
tery from early discharge.
The bracket can be fixed to the surface using screws. Use appropriate screws and
wall plugs, depending on the surface.
The adhesive surface on the bottom of the bracket may only be used if the monitor
e.g. is to be fixed on a table.
Make sure when screwing into place or when drilling holes that cables or wires are
not damaged.
video input 1
audio input 1
video input 2
Connection for power supply, 12 V/DC, 600 mA
Please note: The audio signal on audio input 1 will be muted, if you switch to video
input 2.