Maintenance - HQ Power VDPL300MR Bedienungsanleitung

Termina ation
A DMX te erminator is reco
cable has s to run a long d
environm ment (e.g. discos
digital co ontrol signal by
simply an n XLR plug with
which is t then plugged in
the chain n. Please see illu
DMX Sta art Address
All DMX-c controlled devic
correct d evice responds
channel n number from wh
controller r. Enter the cor
located o on the base of th
You can u use the same st
or enter an individual on
When all devices have th
particula r channel. In ot
simultane eously. If you s
Changing g the settings of
In the ca se of the 2-cha
the secon nd projector to
DMX Val lues per Chann
Chann el Func
1 Operatin
2 Motor r
8. Ma intenance
Disconn
• Let the e projector cool
• To ma intain optimum
genera al rule, fixtures
perform mance and can
wear. Use a vacuum o
• The cle eaning of extern
output t. Cleaning frequ
or part ticularly dirty su
with a soft cloth using
Always s dry the parts c
• There are no user-ser
to be c carried out by a
• Only re eplace a burned
o Befo ore replacing th
o Wed dge the fuse ho
o Rem move the old fus
o Rep place the fuse ho
• Please e contact your H
07.12.201 0
ommended for installations wh
distance or is in an electrically
s). The termina tor prevents co
electrical noise. The DMX term
a 120 Ω resisto or between pins
nto the XLR outp put socket of the
ustration.
ces need a digita al start address
to the signals. This start addre
hich the device starts to "listen
rect number an d read it from t
he projector.
tarting address for a whole gro
ne for every dev vice.
he same addres ss, all the projec
ther words: cha nging the settin
et different add resses, each de
f one channel w will only affect th
nnel projector, you will have to
3 (1 + 2), the t third to 5 (3 + 2
nel
ction Fro om
00 00
ng mode 01 15
10 01
00 01
rotation 08 86
17 71
nect from the m mains before s
down before cl eaning.
performance a nd minimize we
should be clean ned at least twic
cause overheat ting. This can le
or air compress or and a soft br
nal optical lense es and/or mirror
uently depends on the environm
urroundings can n cause greater
g normal glass c cleaning fluid. C
carefully after c cleaning them.
rviceable parts i inside except fo
uthorized perso onnel only.
d fuse by a fuse of the same ty
e fuse, unplug t the projector fro
lder on the rear r panel out of its
se and replace w with a new one.
older in the hou using.
HQPower™ deale er for spare part
VDPL300 0MR
here the DMX
noisy
rruption of the
inator is
s 2 and 3,
e last device in
so that the
ess is the
n" to the DMX
the display
oup of devices
ctors will "listen
ngs of one chann
evice will "listen
he device in que
o set the start a
2) and so on.
To
014 no function
100 LEDs on
255 sound control
085 anticlockwise f
170 clockwise from
255 right to left to
starting mainte
ear, fixtures sho
ce a month. Dus
ead to reduced l
rush to remove
rs must be carri
ment in which t
accumulation o
Clean the extern
r the fuse. Main
pe and rating:
om the mains.
s housing with a
ts or should you
6 6
" to the control signal on one
nel will affect al l devices
" to a separate channel numbe
estion.
address of the fi rst projector to
Descriptio on
from slow to fas st
m slow to fast
right from slow w to fast
enance operati on!
ould be cleaned frequently. As a
st build-up redu uces the light ou
amp life and inc creased mechan
dust collected o on external vent
ied out periodic ally to optimize
he fixture opera ates. Damp, sm
f dirt on the un it's optics. Clea
nal optics at leas st every 3 week
ntenance and se ervice operation
a fitting screwdr river.
u have further q questions.
Re ev. 01
er.
1,
a
utput
nical
ts.
light
moky
n
ks.
s are
©Vellema an nv