Mains Connection; Technical Data; Operation - MC Crypt LCB001 Bedienungsanleitung

Acceptance test (in case of industrial/public use):
Before using the product for the fi rst time and after any signifi cant modifi cations, the
installation (including the electrical connections) must be checked by a specialist.
An annual check by a technical expert is required.
At least every four years, an acceptance inspection must be carried out by a technical
expert.
• Install the effect beamer using the holes provided in the housing on the ceiling, the wall or on a
suitable crossbeam. When installing it, make sure that the device cannot swing freely.
• Secure the device with fastenings that are compatible with the fastening surface and suitable for
carrying the weight of the light effect device.
• Set the desired angle of inclination and carefully tighten the two U-bolts with the provided Allen key.
• Secure the installation with an additional suitable safety restraint cable or net. The safety restraint
cable or net must be capable of supporting the light effect device in the event of a fault in the main
support system.

Mains Connection

When connecting up the power pack make sure fi rst that the voltage data on the
type plate of the power pack is compatible with the mains voltage available. Do
not connect the power pack if the data doesn't comply with the available mains
voltage. The wrong supply voltage may lead to irreparable damages to the device
and involve risks for the user.
The mains socket must be in close proximity to the device and also be easily
accessible after the power pack is plugged in to ensure its fast and safe discon-
nection from the power grid in case of malfunctioning of the light effect device.
Make sure that the connection cable is not being pinched or damaged by sharp
edges.
If the device is not in use, disconnect the power pack or press the all-pole switch
(with a contact gap of 3 mm) to disconnect the device from any power supply.
• Plug the low-voltage plug of the power pack into the 5 V/DC connection socket (3) on the rear of the
effect spotlight.
• Plug the power pack into the mains socket.

Operation

After connecting the power pack to the power grid, the device is ready for use.
• The ON/OFF switch (4) turns the light effect on and off.
The appliance is switched on when the switch is in position ON and switched off when in position
OFF.
• The STROBE switch activates the fl ashing effect.
When the fl ashing effect is active, the LED projection not only moves but is also switched on and off.
• The MUSIC switch (2) activates the music control.
When the music control is active, the light effect changes in time to the music.
Handling
• Never operate the device with damaged housing or missing covers.
• Light effect devices are not suitable for permanent use. The consistent adherence to the interrup-
tions of operation and use (at least 30 minutes after a maximum operating time of 6 hours) increases
the operating life considerably.
• Never plug the power pack into a mains socket immediately after the device has been taken from a
cold environment into a warm one. The condensation that forms might damage the device. Allow the
device to reach room temperature before connecting it. Wait until the condensation has evaporated.
• Never unplug the power packs from the mains socket by pulling on the cable; always use the grips
intended for this purpose.
• Unplug the power pack if you are not going to use the device for a while.
• For safety reasons, always disconnect the power unit from the mains socket during thunderstorms.
• To ensure suffi cient ventilation, never cover the device. In addition, the air circulation must not be
obstructed by objects such as magazines, tablecloths, curtains, decoration material or similar items.
Maintenance and Care
Always pull the power pack out of the mains socket before cleaning the light effect
device.
Make absolutely sure that the inside of the device does not get wet or damp.
Make sure that the area below the place of mounting is blocked off during installa-
tion and service work.
The product should be cleaned regularly to remove dust, etc.
The outside of the device should be cleaned with a soft, dry or slightly damp cloth only.
Never use caustic cleaning agents or chemical solutions, as they could damage the surface of the
casing.
Due to the long service life of the LEDs, there is no need to change the light bulbs.
Disposal
Electronic devices are recyclable waste materials and must not be disposed of in the
household waste!
Dispose of an unserviceable product in accordance with the relevant statutory regula-
tions.

Technical Data

Operating voltage 100-240 V/50/60 Hz (power pack)
5 VDC/1 A (LED effect spotlight)
Power input 3.5 W
Light bulb 3 high-performance LEDs (red/green/blue)
Connection cable approx. 1.5 m
Weight 220 g
Operating temperature range 10-50 °C
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.