Stopwatch Function; Technical Data; Maintenance And Cleaning - Conrad 67 20 01 Bedienungsanleitung

Setting the Time
Step 1:
Move the „12HR/24HR" switch (13) to the position 12HR to display the time in
the 12 hour format (AM or PM will be displayed).
Move the „12HR/24HR" (13) switch to the position 24HR to display the time in
the 24 hour format.
Step 2:
• Press and hold down the „TIMER/CLOCK" button (4), for approx. 2 seconds. The time display
starts to flash.
• Set the desired time using the buttons „HOUR" (5; = hour setting), „MIN" (6; = minutes setting),
„SEC" (7; = seconds setting).
• Press the „TIMER/CLOCK" (4) button, to save these settings.
Switching between Time Mode and Timer Mode
By pressing the „TIMER/CLOCK" button (4) briefly, you can switch between the time mode or
the timer mode.
In the time mode, the current time, as well as a stopwatch with hours, minutes, seconds and 1/10
seconds, is displayed.
In the timer mode, 3 timers with hours, minutes, seconds are displayed.

Stopwatch Function

• Press the „START/STOP" (9) key, while in the time mode. After this, the stopwatch function
starts.
• Press the "STOP/STOP" button (9) again, to stop the stopwatch function.
• Press the „CLEAR" (8) button, to reset the stopwatch to 00:00:00.
Timer Function (Countdown)
Example for setting and starting timer 1:
• While you are in timer mode, press the „TIMER1" (1) button and hold it pressed for approx.
2 seconds. The timer display starts to flash.
• Set the desired time for the timer using the buttons „HOUR" (5; = hour setting), „MIN" (6; = min-
utes setting), „SEC" (7; = seconds setting).
• Press the „TIMER1" button (1), to save the settings.
• Press the "TIMER1" button (1), to start the TIMER countdown.
Please note that all three TIMERS can be started simultaneously. In this case,
set all three timers as required, and then press the „START/STOP" (9) button,
instead of the corresponding timer button.
• When the timer countdown is activated, press the „TIMER1" (1) button to pause the timer
countdown. Press the „TIMER1" button (1) again, to resume the countdown.
When the time has run down, an alarm signal is emitted for 1 minute. In addi-
tion, a countdown starts to indicate when the corresponding countdown
timer elapsed. To stop the started countdown timer press the „START/STOP"
(9) button. To reset the timer, press the „CLEAR" (8) button. Then, press the
„START/STOP" key (9), to select the last set countdown period.
To set timer 1 and timer 2, proceed as described above. To do this, use the buttons „TIMER2"
or „TIMER3" respectively, instead of the „TIMER1" (1) button.

Maintenance and Cleaning

Use a clean, dry, soft cloth for cleaning. If it is very dirty, use a cloth slightly moistened with luke-
warm tap water.
Clean the timer very carefully, otherwise you may scratch it. Do not press too strongly on the dis-
play as this may cause damage.
Disposal
a) In general
Please dispose of the device when it is no longer of use, according to the current statutory
requirements.
b) Batteries and rechargeable batteries
As a consumer you are required (Battery Ordinance) to responsibly dispose of all used batter-
ies and rechargeable batteries; it is forbidden to throw them away with the normal house-
hold waste!
Contaminated batteries/rechargeable batteries are labelled with these symbols to
indicate that disposal in the domestic waste is forbidden. The designations for the
heavy metals involved are: Cd = cadmium, Hg = mercury, Pb = lead.
Used batteries, rechargeable batteries as well as coin cells can be returned to col-
lection points in your municipality, our stores or wherever batteries/rechargeable
batteries/coin cells are sold!
You thus fulfil the legal requirements and make your contribution to protecting the environment!

Technical Data

Power supply:
Max. countdown that can be set:
Dimensions (W x H x D):
Weight:
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2009 by Conrad Electronic SE.
2 x 1.5V/DC button cell (type: LR44).
19 hours, 99 minutes, 99 seconds
approx. 60 x 100 x 19 mm
approx. 70 grams