Makita BSR730 Bedienungsanleitung Seite 6

ENGLISH
1 To avoid kickback, do support
board or panel near the cut.
2 Don't support board or panel
away from the cut.
3 A typical illustration of proper
hand support and workpiece
support.
4 Button
5 Battery cartridge
6 Battery charger
7 Charging lights
8 Terminal cover
9 Hex wrench
10 Loosen (counterclockwise)
11 Shaft lock
SPECIFICATIONS
Model
Blade diameter ....................................................190 mm
Max. cutting depth
At 90° ..................................................................66 mm
At 45° ..................................................................47 mm
At 50° ..................................................................42 mm
–1
No load speed (min ) ............................................ 2,400
Overall length ......................................................378 mm
Net weight ..............................................................4.6 kg
Rated voltage .................................................... D.C.24 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
6
Explanation of general view
12 Saw blade
13 Outer flange
14 Bolt
15 Inner flange
16 Setting protuberances
17 Hex socket head bolt
18 Cutting depth
19 Lever
20 Clamp screw
21 Lever
22 Slant surface
23 Base
24 Adjusting screw for 90°
25 Adjusting screw for 45°
26 Triangular rule
8.
BSR730
9.
10. Do not disassemble charger or battery cartridge;
11. To reduce risk of electric shock, unplug charger
12. The battery charger is not intended for use by
13. Young children should be supervised to ensure
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1.
ENC002-2
2.
3.
4.
5.
6.
7.
27 For 45° bevel cuts
28 For straight cuts
29 Base plate
30 Cutting line
31 Lock-off button
32 Switch trigger
33 Rip fence (Guide rule)
34 Dust nozzle
35 Screws
36 Hose 28 mm in inner dia.
37 Vacuum cleaner
38 Limit mark
39 Brush holder cap
40 Screwdriver
Do not operate charger with damaged cord or
plug — replace them immediately.
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
young children or infirm persons without super-
vision.
that they do not play with the battery charger.
Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
Do not allow anything to cover or clog the
charger vents.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop, shake or strike battery.