Installation - EuroLite LED UMBRELLA 95 Bedienungsanleitung

INSTALLATION

WARNING! Risk of injury caused by falling objects
Devices in overhead installations may cause severe injuries when crashing down. Make sure
that the device is installed securely and cannot fall down. The installation must be carried out by
a specialist who is familiar with the hazards and the relevant regulations.
The device may be placed via the enclosed mounting adapter on a lighting stand or fastened with an
appropriate clamp to a truss or similar rigging structure. The device must never be fixed swinging freely in
the room.
1 The rigging structure must support at least 10 times the weight of all fixtures to be installed on it.
2 Block access below the work area and work from a stable platform when installing the device.
3 Use rigging hardware that is compatible with the structure and capable of bearing the weight of the
device. Please refer to the "Accessories" section for a list of suitable rigging hardware.
4 Secure the device with a safety bond or other secondary attachment. This secondary safety attachment
must be sufficiently dimensioned in accordance with the latest industrial safety regulations and
constructed in a way that no part of the installation can fall down if the main attachment fails.
5 After installation, the device requires inspections periodically to prevent the possibility of rot, deformation
and looseness.
Installation on a lighting stand
Please note: All devices, lighting effects and crossbeams attached on a stand must be secured with a
secondary attachment!
1 First, loosen the fixation screws at the stand's levelling feet. Pull out the levelling feet until the cross
struts and the levelling feet form a 90° angle. Now retighten the fixation screws.
2 Remove the tip of the top of the umbrella and put the top of the umbrella through the umbrella intake of
the adapter. Now reattach the tip and tighten the two crosshead screws of the adapter in order to fix the
tip in the adapter.
3 Attach a crossbeam adapter or TV pin to the upper end of the stand and tighten it with the fixation
screw.
4 Fix the enclosed mounting adapter to the TV pin and tighten the pin's fixation screw.
5 Carefully span the umbrella. Loosen the adapter's fixation screws, set the desired tilt and firmly
retighten the screws in order to align the device.
6 Remove the extension bar inside the umbrella and put it aside for dismantling the device later. Put the
LED module on top of the remaining, shortened bar inside the umbrella. Now firmly tighten the knurled
head screws in order to fix the LED module inside the umbrella.
7 Caution! The stand requires an even load distribution. The maximum load must never be exceeded. The
lighting stand must stand firmly on the ground. Make sure that all fixation screws are firmly tightened.
8 The cutout on the umbrella is necessary for the wiring.
9 After installation, the device requires inspections periodically to prevent corrosion, deformation and
loosening.
Installation on a crossbeam
1 Remove the end of the tip of the umbrella and put the tip through the adapter's umbrella intake. Reattach
the tip. Tighten the adapter's crosshead screws in order to fix the tip inside the adapter.
2 Use a M10 screw and a self-locking nut to screw a hook to the adapter.
3 Use the adapter to attach the device to your crossbeam system.
4 Insert the quick link of the safety rope into the adapter's attachment eyelet and pull the safety rope over
the crossbeam or another safe fixing point. Then insert the end of the rope into the quick link and firmly
tighten the fixation screw.
5 The control unit may be placed on the floor or fastened to a truss or similar rigging structure. The device
must never be fixed swinging freely in the room. Screw a clamp via a M10 screw and self-locking nut
onto the omega-holder. Insert the two screws of the enclosed omega-holder into the respective holes on
the bottom of the device. Tighten the screws fully. Use a safety rope or another appropriate structure as
secondary attachment for the control unit. Fully screw the safety eyelet into the bottom of the control unit.
Insert the quick link of the safety rope into the safety eyelet in the bottom and pull the safety rope over
the crossbeam or another safe fixing point. Insert the rope's end into the quick link and firmly tighten the
fixation screw.
6 The device's drop distance must not exceed 20 cm. Fix the safety rope respectively.
20/28 00117302.DOCX, Version 1.1