Safety Regulations; Layout And Items Supplied - EINHELL TC-EW 160 D Originalbetriebsanleitung

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Safety components:
a) Danger from electric shock: An electric
shock from a welding electrode can be fatal.
Never perform any welding in rain or snow.
Wear dry insulating gloves. Do not touch the
electrode with your bare hands. Do not wear
wet or damaged gloves. Protect yourself from
an electric shock by insulating yourself from
the workpiece. Do not open the equipment
housing.
b) Danger from welding fumes: The inhaling
of welding fumes can harm your health. Keep
your head out of the fumes. Use the equip-
ment in open areas. Use a ventilation system
to remove the fumes.
c) Danger from welding sparks: Welding
sparks can cause an explosion or fi re. Keep
combustible materials away from the welding
area. Do not weld combustible materials.
Welding sparks can cause fi res. Keep a fi re
extinguisher nearby and someone watching
who can use it immediately. Do not weld on
drums or any closed containers.
d) Danger from welding arc radiation: Wel-
ding arc radiation can damage your eyes and
injure your skin. Wear a hat and safety gog-
gles. Wear ear protection and a high, closed
shirt collar. Use a welding helmet and fi lters of
Anl_TC_EW_160_D_SPK9.indb 16 Anl_TC_EW_160_D_SPK9.indb 16
GB
the correct size. Wear complete body protec-
tion.
e) Danger from electromagnetic fi elds: Wel-
ding current creates electromagnetic fi elds.
Do not use together with medical implants.
Never wind the welding cables around your
body. Guide welding cables together.

2. Layout and items supplied

2.1 Layout (Fig. 1)
1. Electrode holder
2. Earth terminal
3. Adjustment wheel for welding current
4. Selector switch 230 V / 400 V
5. Control lamp for overheating
6. Welding current scale
7. Carry handle
8. Power cable 400 V
9. 230 V mains cable
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
•
Welding set
•
Original operating instructions
•
Safety instructions
- 16 -
26.07.2017 09:01:00 26.07.2017 09:01:00