Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
B. Starting up
B.2 Unpacking and assembling
Remove transport and security devices: (*)
- Slide cover plate to rear and remove
- Remove transport safety device (from ribbon spools)
- Tighten ribbon by turning spool
- Replace cover plate, slide forward and secure
Connection to power supply:
- Check that the data on the data plate coincides with the local vol-
tage before connection calculator to power supply.
- Connect calculator to power supply.
Inserting the paper roll (Art. No. 9367):
- Fit the paper roll holder
- Roll out paper, leading edge to the top, into the guides
- Turn calculator on
- Paper is drawn into paper slot
- Feed paper as far as possible until it stops at the rear opening
- Use
to insert the paper further
Turning ON / OFF:
When turned on, the calculator is ready to operate.
At least 3 seconds should elapse between turning on and off
again.
B.3 General information
Accumulator:
Products, quotients and individual value can be totaled and stored
in the accumulator. Multiplication and division are ignored.
Entries:
Value and sub-totals are transmitted directly to the accumulator via
the addition and subtraction keys.
Constants:
The multiplicand, divisor, basic value or percentage, including the
subsequent function, are automatically retained as constants.
Repeat value:
Using the basic calculation modes, a value can be repeatedly used
as often as required.
Paper roll printout:
The decimal place is printed as a point. Examples:
CPD 3212, CPD 5212
1 234 567 890.12 +
Entering values and calculation methods:
- Addition / Subtraction (a+b+c+)
t
Result via
- Multiplikation / Division (axb c=)
Result via
=
Triad group symbols (commas) shown in display:
Values to the left of the decimal point are divided by triad symbols.
Example:
1,234,567,890.12
Capacity overflow:
When results exceed 12 full digits "...................." (CPD 3212) or
"ERROR" (*) is printed out, a "E" appears in the display and the
keyboard is blocked for entry. To release the keyboard;
press:
or
or
for (* 5212).
CE
E
Memory block:
The memory will not accept a value which would exceed the me-
mory capacity. The memory contents remain unaltered.
Item counter (Switch position):
When activated a 3 digit item counter is provided for the accumula-
tor and for the memory.
By pressing
+
and
–
or
M+
and subtractions are counted.
The number of item is printed on requesting sub-totals or final to-
tal. Example:008 = 8 items.
008
600.00_
Pressing the final total key clears the counter.
and
M–
the number of additions
Stored rates & memory contents retained:
The memory contents and stored rates of conversion, tax and %
will be retained even if the calculator is turned off.
The 11 pre-programmed fixed Euro rates are available for different
countries (refer "Currency code table" page 31.) and are originally
installed in the calculator. It is not possible to change such
preprogrammed rate at any time.
Currency conversion:
- The conversion rate consists of 6 significant figures with the deci-
mal points.
- Additionally, 5-currency conversion rates can be programmable
and stored.
- To convert between '1st currency' and '2nd currency' through
conversion rate, the 1st currency and the 2nd currency will be se-
lect among 'Euro', 'originally installed 11-currency' and 'stored 5-
currency'.
- Conversion rate is printed out with the symbol of R#.
- Euro currency can be printed out with the following symbol mark:
E
---- CPD 3212
5
---- CPD 5212 (*)
- Refer to "Currency code table" page 31.
Tax Rate:
- Tax rate consists of 6 significant figures with decimal point.
- Tax rate is printed out with the symbol of RT.
Automatic %+ calculation (percent add-on):
- Automatic %+ calculation can proceed with user stored % rate or
entry % rate.
- The user stored % rate consists of 6 significant figures with deci-
mal point.
- Stored % rate is printed out with the symbol of R%.
B.4 Keyboard summary
The keyboard has an input buffer which enables all entries, regard-
less of speed of input, to be proceeded in order of input.
C
Total clearance
- The complete calculation process is cleared. Memory con-
tents are retained.
- The stored rates are retained even after depressing this
key.
Recall item counter
n
- Press once:
Recall number of added items
- Press twice, after recall of final sum or sub-total:
Recall arithmetic mode average of item addition and sub-
traction.
Non-add key
#
- Date or number printout.
CE
Correction key
- Clear entered value.
Algebraic sign change key
+/-
- To specify a positive or negative value.
Digit keys
0
–
9
- The values entered appear in the display.
.
Decimal point key
–
Subtraction key
Addition key
+
Sub-total key
- Recall accumulator / item counter contents
t
Final total key
- Recall and clear accumulator / item counter contents
%
Percent key
Together with
:
x
- Recall percent value.
Together with
and
x
- Recall the value plus or minus the percent value.
Division key
_
or
:
+
7
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
