Herunterladen Inhalt Inhalt Diese Seite drucken

Ferm PDM1016 Originalbetriebsanleitung Seite 6

Vorschau ausblenden Andere Handbücher für PDM1016:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 8
ASSEMBLy
4
Before assembly, always switch off the
machine and remove the mains plug
from the mains.
Mounting and removing the drill bit (fig. B)
The machine is suitable for use of the following
drill bits:
-
Wood (HSS)
-
Metal (HSS)
-
Concrete / masonry (hard metal)
Mounting
● Place the chuck key (12) into one of the holes
in the chuck (7).
● Open the chuck (7) by turning the chuck key
(12) counterclockwise.
● Insert the drill bit (14) into the chuck (7).
● Close the chuck (7) by turning the chuck key
(12) clockwise.
● Remove the chuck key (12) from the chuck (7).
Removing
● Place the chuck key (12) into one of the holes
in the chuck (7).
● Open the chuck (7) by turning the chuck key
(12) counterclockwise.
● Remove the drill bit (14) from the chuck (7).
● Close the chuck (7) by turning the chuck key
(12) clockwise.
● Remove the chuck key (12) from the chuck (7).
Mounting and removing the auxiliary grip
(fig. C)
Mounting
● Loosen the auxiliary grip (9).
● Slide the auxiliary grip (9) over the chuck (7).
● Turn the auxiliary grip (9) to the required
position.
● Tighten the auxiliary grip (9).
Removing
● Loosen the auxiliary grip (9).
● Remove the auxiliary grip (9) from the chuck (7).
● Tighten the auxiliary grip (9).
Mounting and removing the depth stop (fig. D)
The depth stop is used to set the maximum
drilling depth.
Mounting
● Loosen the auxiliary grip (9).
● Insert the depth stop (10) through the hole in
the auxiliary grip (9).
6
● Set the depth stop (10) to the required position.
● Tighten the auxiliary grip (9).
Removing
● Loosen the auxiliary grip (9).
● Remove the depth stop (10) from the auxiliary
grip (9).
● Tighten the auxiliary grip (9).
USE
Switching on and off (fig. A)
● To switch on the machine, press the on/off
switch (1). The further the on/off switch (1) is
pressed, the higher the speed of the machine.
● To switch the machine to continuous mode,
keep the on/off switch (1) pressed and
simultaneously press the lock-on button (2).
● To switch off continuous mode, press the
on/off switch (1) again.
● To switch off the machine, release the
on/off switch (1).
Forward/reverse switch (fig. A)
2
Do not change the direction of rotation
during use.
● For clockwise rotation, slide the forward/
reverse switch (4) to the left.
● For counterclockwise rotation, slide the
forward/reverse switch (4) to the right.
Setting the maximum drilling speed (fig. A)
2
Do not set the speed during use.
● Turn the speed adjustment wheel (3) clockwise
to increase the maximum drilling speed.
● Turn the speed adjustment wheel (3)
counterclockwise to decrease the maximum
drilling speed.
Setting the mechanical drilling speed (fig. A)
2
Do not set the speed during use.
● If you set the switch (5) to position "1",
the drilling speed can be continuously adjusted
between 0 and 1,100 min
● If you set the switch (5) to position "2",
the drilling speed can be continuously adjusted
between 0 and 3,000 min
.
-1
.
-1

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis