Auxiliary Handle; Changing The Tool - Bosch 650 RE Originalbetriebsanleitung

OBJ_BUCH-911-003.book Page 24 Tuesday, November 23, 2010 3:18 PM
24 | English
When the extraction force diminishes or when
the level indicator 13 is full, the dust collector
12 must be emptied. For this, press on the rif-
fled surface of the release button 16 and take
off the dust collector 12.
Empty and clean the dust collector 12. Clean the
filter element 17 by gently striking or tapping
against it.
Check the filter element 17 for damage and re-
place it as required.
Press on the holder of the filter element 17 and
pull it out. Replace the filter element 17 includ-
ing the holder. When placing on the holder
again, make sure that the rubber gasket 18 is in-
serted.
Reattach the dust collector 12 again and lock it
by pressing against the smooth surface of the
release button 16.
Removing the Extraction Device (see figure E)
For disassembly of the extraction device 11,
press release button 20 and pull off the extrac-
tion device 11 toward the front.
Stowing the Extraction Device (see figure F)
For stowing the extraction device 11 in the case,
remove the extraction device 11, slide it togeth-
er and attach clamp 21.
Attach the locking latch 22 or empty the dust
collector 12 before placing down the extraction
device.

Auxiliary Handle

Operate your machine only with the auxilia-
ry handle 9.
The auxiliary handle 9 can be set to any position
for a secure and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxilia-
ry handle 10 in anticlockwise direction and set
the auxiliary handle 9 to the required position.
Then tighten the wing bolt 10 again in clockwise
direction.
Adjusting the Drilling Depth (see figure G)
The required drilling depth X can be set with the
depth stop 1.
2 609 005 110 | (23.11.10)
Press the button for the depth stop adjustment
3 and insert the depth stop into the auxiliary
handle 9.
The knurled surface of the depth stop 1 must
face downward.
Pull out the depth stop until the distance be-
tween the tip of the drill bit and the tip of the
depth stop correspond with the desired drilling
depth X.

Changing the Tool

Keyless Chuck (PSB 750 RCE/PSB 750 RCA)
(see figure H)
The drill spindle is locked when the On/Off
switch 8 is not pressed. This makes quick, con-
venient and easy changing of the tool in the drill
chuck possible.
Open the keyless chuck 2 by turning in rotation
direction , until the tool can be inserted. Insert
the tool.
Firmly tighten the collar of the keyless chuck 2
by hand in rotation direction
action ("click") is no longer heard. This automat-
ically locks the chuck.
The locking is released again to remove the tool
when the collar is turned in the opposite direc-
tion.
Keyless Chuck (PSB 650 RE/ PSB 6500 RE/
PSB 650 RA) (see figure I)
Press the spindle lock button 25 only when
the machine is at a standstill.
The drill spindle is locked by pressing the spin-
dle lock button 25. This makes quick and easy
changing of the tool in the drill chuck possible.
Open the keyless chuck 2 by turning in rotation
direction , until the tool can be inserted. Insert
the tool.
Firmly tighten the collar of the keyless chuck 2
by hand in rotation direction
action ("click") is no longer heard. This automat-
ically locks the chuck.
The locking is released again to remove the tool
when the collar is turned in the opposite direc-
tion.
until the locking
until the locking
Bosch Power Tools