Technical Data; Operation - Renkforce YTSL-06 Mini Laser Bedienungsanleitung

Installation/Set-up
T he assembly and the installation of the device must be carried out by a
specialist who is familiar with the hazards and the relevant regulations.
Repairs, operation and maintenance of the product may only be carried out
by qualified personnel.
D o not place or install the device where it will be exposed to shaking, vi-
bration, dust, heat, cold and moisture. Furthermore, keep the product away
from strong transformers or motors.
The device must be mounted out of normal reach.
W hen installing the product, ensure that the adapter's power cord is not
jammed or damaged by sharp edges.
D uring installation and servicing, the area below the installation site must
be cordoned off.
T he installation surface, or mounting fixture, must be designed so that it
can withstand 10 times the loading capacity for at least one hour without
permanent damaging deformation.
I t is also essential that the device is secured by means of a second safety
restraint, which is separate from the proper mounting supports, when it is
installed in an elevated position. If the main supports fail, no part of the
installation should be able to fall down.
O bserve all the relevant regulations when mounting/installing the device.
K eep a free area of 15 cm around the housing to ensure unhindered heat
dissipation. Otherwise, the laser may overheat.
The laser can be set up on the enclosed tripod or attached to the ceiling or wall.
Installation on the tripod
• Screw the tripod to the tripod socket on the bottom of the housing.
• Align the feet of the tripod, and thereby also the direction of the laser, as desired.
Installation with a mounting bracket
• Install the laser effect device using a mounting bracket on the ceiling, the wall or on
a suitable crossbeam. When installing it, make sure that the device cannot swing
freely.
• Secure the device with fastenings that are compatible with the fastening surface
and suitable for carrying the weight of the laser.
• Secure the installation with an additional suitable safety restraint cable or net. The
safety restraint cable or net must be able to support the light effect device in the
event of a fault in the main support system.
• Set the desired angle of inclination and tighten the two bracket locking screws ca-
refully.
Connecting the power adapter
T he mains socket to which the laser is connected must be easily accessib-
le so the device can be quickly and easily separated from the mains voltage
in the case of a fault.
D o not let the mains cable come into contact with other cables.
B e careful when handling the mains cables and mains connectors. Mains
voltage can cause serious electric shocks, which can be fatal.
D o not leave the cables trailing free; route them in an orderly and professi-
onal way to prevent accidents.
• Plug the enclosed power adapter's low-voltage plug into the DC-5 V socket.
• Plug the power adaptor into a wall socket.

Operation

The desired operation mode is selected by means of the functional switch 1-2-3 and
the MUSIC/AUTO switch:
• 1-2-3 Switch position 1
The laser effect flashes.
Use the STROBOFLASH CONTROLLER to set the flashing frequency.
Use the MOTOR CONTROLLER to set the rotational speed of the motor.
• 1-2-3 Switch position 2
The laser effect device remains switched on.
Use the MOTOR CONTROLLER to set the rotational speed of the motor.
• 1-2-3 Switch position 3
The device is switched off.
• MUSIC/AUTO Switch
MUSIC: The laser effect is controlled by the beat of the music.
AUTO: The laser effect is now controlled via the integrated controller.
Handling
• Never switch the laser effect device on and off at short intervals. This will consi-
derably reduce the working life of the device.
• The device is not suitable for continuous use. Pauses in operation increase the wor-
king life of the product.
• Never switch the device on immediately after it has been taken from a cold room
into a warm one. The condensation that forms might damage the device.
Leave the device disconnected and wait until it has reached room temperature.
Wait until the condensation has evaporated.
• To ensure sufficient ventilation, never cover the device. In addition, the air circula-
tion must not be obstructed by objects such as magazines, tablecloths, curtains or
similar items.
Maintenance and care
B efore cleaning the laser, disconnect it from the power supply (disconnect
the power supply unit).
M ake absolutely sure that the inside of the device does not get wet or
damp.
The outside of the device should be cleaned with a soft, slightly damp cloth or dry
brush.
Never use aggressive cleaning agents or chemical solutions, as these may damage
the surface of the case.
Disposal
Electronic devices are recyclable waste materials and must not be disposed
of in the household waste!
Dispose of an unserviceable product in accordance with the relevant statu-
tory regulations.
Technical data
Operating voltage of power adapter .............. 100 - 240 V/50/60 Hz
Operating voltage of laser ................................ 5 V/DC
Power consumption........................................... 0.2/4W Standby/max.
Laser output ........................................................ <1 mW
Wavelength ......................................................... 532/650 nm
Laser class .......................................................... 2
Operating conditions ......................................... 10 °C - 35 °C / 45% - 90% rel. humidity
Dimensions (without mounting bracket) ........ 128 x 92 x 51 mm
Weight .................................................................. 320 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.