Connecting The Units - Pioneer DEH-7200SD Installationsanleitung

8. Notes 1. This product
• Change the initial setting of this unit (refer to the
operation manual). The subwoofer output of this unit is
monaural.
7. Antenna
• When using a subwoofer of 70 W (2 Ω), be sure to
jack
connect with Violet and Violet/black leads of this unit.
Do not connect anything with Green and Green/black
6. Fuse (10 A)
leads.
9. Note
Depending on the kind of vehicle,
the function of 2* and 4* may be
different. In this case, be sure to
connect 1* to 4* and 3* to 2*.
2* 1*
4* 3*
10. Connect leads of the
same color to each other.
11. Yellow (2*) 12. Yellow (1*)
Back-up (or Connect to the constant
accessory) 12 V supply terminal.
13. Red (4*) 14. Red (3*)
Accessory Connect to terminal controlled by
(or back-up) ignition switch (12 V DC).
15. Orange/white
Connect to lighting switch terminal.
16. Black (chassis ground)
Connect to a clean, paint-free metal location.
17. ISO connector 18. Yellow/black
Note If you use an equipment with Mute
In some vehicles, the ISO connector may be function, wire this lead to the Audio Mute
lead on that equipment. If not, keep the
divided into two. In this case, be sure to
Audio Mute lead free of any connections.
connect to both connectors.
23. To rear output
2. Rear output
24. To front output
3. Front output
4. Subwoofer output
25. To subwoofer output
26. Power amp
5. Wired remote input
(sold separately)
Hard-wired remote
control adaptor can
be connected (sold
separately).
27. Connect with RCA cables
(sold separately)
28. System remote control
19. Blue/white
Connect to system control  
29. Subwoofer 29. Subwoofer
terminal of the power amp (max.
 
300 mA 12 V DC).
20. Blue/white (6*)
 
Connect to auto-antenna relay
30. Front speaker 30. Front speaker
control terminal (max. 300 mA
 
12 V DC).
21. Blue/white (5*)  
31. Rear speaker 31. Rear speaker
The pin position of the ISO
 
connector will differ depending
32. Perform these connections when
on the type of vehicle. Connect
5* and 6* when Pin 5 is an using the optional amplifier.
antenna control type. In another
type of vehicle, never connect
5* and 6*.
22. Speaker leads
White: Front left 
White/black: Front left 
Gray: Front right 
Gray/black: Front right 
Green: Rear left  or subwoofer 
Green/black: Rear left  or subwoofer 
Violet: Rear right  or subwoofer 
Violet/black: Rear right  or subwoofer 
Connecting the units
Note
• When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
26. Power amp
red cable must be wired to the terminal that can
(sold separately)
detect the operation of the ignition key. Otherwise,
battery drain may result.
26. Power amp
(sold separately)
ACC position No ACC position
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
against metal parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's
negative cables.
English Connecting the units
Connection Diagram
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
1. This product
external power amp's system remote control or
2. Rear output
the vehicle's auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is equipped 3. Front output
with a glass antenna, connect it to the antenna
4. Subwoofer output
booster power supply terminal.
5. Wired remote input
• Never connect blue/white cable to external power
Hard-wired remote control adaptor can be
amp's power terminal. Also, never connect
connected (sold separately).
it to the power terminal of the auto antenna.
6. Fuse (10 A)
Otherwise, battery drain or malfunction may
7. Antenna jack
result.
8. Notes
• Black cable is ground. This cable and other
product's ground cable (especially, high-current • Change the initial setting of this unit (refer
products such as power amp) must be wired
to the operation manual). The subwoofer
separately. Otherwise, fire or malfunction may
output of this unit is monaural.
result if they are accidentally detached.
• When using a subwoofer of 70 W (2 Ω), be
sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything
with Green and Green/black leads.
9. Note
Depending on the kind of vehicle, the function
of 2* and 4* may be different. In this case, be
sure to connect 1* to 4* and 3* to 2*.
10. Connect leads of the same color to each other.
11. Yellow (2*)
Back-up (or accessory)
12. Yellow (1*)
Connect to the constant 12 V supply terminal.
13. Red (4*)
Accessory (or back-up)
14. Red (3*)
Connect to terminal controlled by ignition
switch (12 V DC).
15 Orange/white
Connect to lighting switch terminal.
16. Black (chassis ground)
Connect to a clean, paint-free metal location.
17. ISO connector
Note
In some vehicles, the ISO connector may
be divided into two. In this case, be sure to
connect to both connectors.
English
18. Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
19. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
20. Blue/white (6*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
21. Blue/white (5*)
The pin position of the ISO connector will differ
depending on the type of vehicle. Connect 5*
and 6* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 5*
and 6*.
22. Speaker leads
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left + or subwoofer +
Green/black: Rear left * or subwoofer *
Violet: Rear right + or subwoofer +
Violet/black: Rear right * or subwoofer *
23. To rear output
24. To front output
25. To subwoofer output
26. Power amp (sold separately)
27. Connect with RCA cables (sold separately)
28. System remote control
29. Subwoofer
30. Front speaker
31. Rear speaker
32. Perform these connections when using the
optional amplifier.