Installation; Box Contents - Philips SBCVL1205/00 Bedienungsanleitung

Congratulations
The Philips W Philips W Philips W Philips W Philips Wi r i r i r i r i reless TV Link Receiver SBC VL1205 eless TV Link Receiver SBC VL1205 eless TV Link Receiver SBC VL1205 eless TV Link Receiver SBC VL1205 eless TV Link Receiver SBC VL1205 you have just purchased is
GB
manufactured to the highest standards and will give you years of trouble-free use. The
Philips Wireless TV Link Receiver is designed to be used in addition to a Philips Wireless
TV Link, type number SBC VL1200. Please read the following instructions carefully, and
retain this booklet for future reference.
The Philips Wireless TV Link Receiver allows you to receive the video signal transmitted
by a Philips Wireless TV Link in another location. You can, for example, use the Philips
SBC VL1200 Wireless TV Link in your living room to watch a program on a second TV
in your bedroom. This Philips Wireless TV Link Receiver VL1205 allows you to watch the
same transmitted video signal in another location (e.g. the TV in your study), regardless
of how many other receivers that you might have.
The Philips Wireless TV Link Receiver is based on wireless RF technology that offers you
freedom of movement and convenience. Because it is wireless it is more susceptible
to outside interference than, for instance, cabled signals. This interference may come from
sources that include microwave ovens or other TV Links in the vicinity. To enable you
to find the best possible performance, the Philips Wireless TV Link Receiver has a channel
selector switch, which enables you to select the channel that provides optimum viewing.

Box contents

• Wireless TV Link Receiver unit.
• One SCART cable.
• One AC power adapter 230V AC, 50 Hz; output voltage 9V DC, 300mA.
• This 'Instructions for Use' booklet.
Requirements
A Philips SBC VL1200 Wireless TV Link, which comprises a Transmitter and Receiver unit,
and a SCART connector on the TV, onto which the receiver will be connected.
S
AFETY
• Do not use this product in moist places or close to water.
• Do not expose this product to extreme heat.
• Do not open this product; in case of technical difficulties bring it to your Philips
retailer.
• Do not cover this product.
• Only connect the AC power adapters to a power supply of 220-240 V AC / 50Hz.
• Only use the AC power adapters included or a type that complies with safety
standard EN60950 and that has the following specification: 9 Volt DC / 300mA.
Y Y Y Y Y our pr our pr our product and its envir our pr oduct and its envir oduct and its envir oduct and its environment onment onment onment
our pr oduct and its envir onment
• Inadequately protected or sensitive electronic equipment may be affected by the use
of this product. This interference can lead to accidents. Please check whether or not
surrounding equipment can be affected by this product before you start using it.
P
RECAUTIONS
2

Installation

There are no limitations to the number of additional Receiver units that can be used
together with a SBC VL1200 Wireless TV Link. In practice you could use three or even
four receivers, but in this booklet the assumption is that one additional Receiver unit is
being used with what we refer to as a 'third' TV for ease of understanding.
The Receiver unit must be installed close to the third TV. Observe the drawings on the
fold out page during the installation procedure.
• Make sure the channel selection switch (figure A-2, figure C-8) of the Receiver unit
is in the same position as the channel selection switch of the Transmitter unit.
• Position the Receiver unit somewhere close to your third TV so that the front of the
unit can receive commands from your remote control.
• Connect a SCART cable from the SCART connector at the back of the Receiver unit
(figure A-1) to the SCART connector at the back of your third TV.
• Plug the cable of the power adapter into the 9V DC socket (figure A-3) at the rear
of the Receiver unit.
• Plug the power adapter into a mains socket.
Controls
The Receiver unit has an on/off POWER button (figure A-4) on the front and a transmission
channel switch (figure A-2) at the rear.
Power on/off switch
• Press the on/off POWER button (figure A-4) to switch on the unit. A green light (figure
A-5) on the right-hand side of the button lights up to show that the unit is switched
on.
Channel selection switch
To allow you to enjoy the best possible performance, both Wireless TV Link Transmitter
& Receiver units are equipped with a channel switch. You can switch between four
channels (or less, depending on local regulations) to select the one that offers the best
possible performance with minimum or no interference. Please note that in all cases the
Transmitter unit and all Receiver units should be switched to the same channel.
• Select the same channel on the Receiver unit as the one you have chosen for your
Wireless TV Link Transmitter and Receiver units (figure A-2).
!
Note Note Note Note Note
Always select the same channel on all Transmitter units and all Receiver units.
3