Safety Instructions; Maintenance - JB Systems CMX-24 Bedienungsanleitung

ENGLISH
®
Thank you for buying this JB Systems product. To take full advantage of all possibilities, please read these
operating instructions very carefully.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
 Scene-setter with 12 up to 24 DMX channels
 48 programs spread over 4 pages
 Chase of the programs (automatic or manual)
 Manual control by 24 faders (speed control, dimming,...)
 Other functions: black-out, tap sync, step change, dimming curve
 Perfect for use on stages and in theaters
BEFORE USE
Check the contents:
Check that the carton contains the following items:
 CMX24
 User manual
 DMX cable
 AC/DC adapter
Some important instructions:
 Before you start using this unit, please check if there's no transportation damage. Should there be any, do
not use the device and consult your dealer first.
 Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused
by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects
or problems caused by disregarding this user manual.
 Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
 To protect the environment, please try to recycle the packing material as much as possible.

SAFETY INSTRUCTIONS:

CAUTION: To reduce the risk of electric shock, do not remove the top cover.
CAUTION
No user-serviceable parts inside. Refer servicing to qualified service
personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use
or the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instructions in the literature accompanying this
appliance.
This symbol means: indoor use only.
This symbol means: Lamp Control Gear
This symbol means: Read instructions.
 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
 This unit is for indoor use only.
JB SYSTEMS
®
OPERATION MANUAL
1/93
ENGLISH
 Don't place metal objects or spill liquid inside the unit. No objects filled with liquids, such as vases, shall be
placed on this appliance. Electric shock or malfunction may result. If a foreign object enters the unit,
immediately disconnect the mains power.
 No naked flame sources, such as lighted candles, should be placed on the appliance.
 Don't cover any ventilation openings as this may result in overheating.
 Prevent use in dusty environments and clean the unit regularly.
 Keep the unit away from children.
 Inexperienced persons should not operate this device.
 Maximum save ambient temperature is 40°C. Don't use this unit at higher ambient temperatures.
 Always unplug the unit when it is not used for a longer time or before you start servicing.
 The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
 Check that the available voltage is not higher than the one stated on the rear panel of the unit.
 The socket inlet shall remain operable for disconnection from the mains.
 The power cord should always be in perfect condition: switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard
 Never let the power-cord come into contact with other cables!
 In order to avoid a hazard, the unit shall only be used with the AC-adaptor delivered with it. If the AC-
adaptor is damaged, a same model adaptor shall be used only.
 In order to prevent electric shock, do not open the cover. Apart from the mains fuse there are no user
serviceable parts inside.
 Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
 In the event of serious operating problems, stop using the appliance and contact your dealer immediately.
 Please use the original packing when the device is to be transported.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
CONNECTIONS
The termination of the signal reduces signal errors and avoids problems with transmission and interruptions.
It's always recommended to connect a DMX signal terminator (a resistor of 120 Ohm 1/4W) between pin2
(DMX-) and pin3 (DMX+) on the last fixture in the chain

MAINTENANCE

Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside the unit. Do not
use volatile liquids such as benzene or thinner which will damage the unit.
CONVENTIONS
In this manual, a button is presented as <BUTTON>
VERY IMPORTANT TO UNDERSTAND THIS MANUAL ARE THE NEXT CONCEPTS:
-Press and release a button: <BLACK OUT>
-Press and hold a button: <RECORD/SHIFT>+
For example: <RECORD/SHIFT> + <CHASE REV>
Press and hold SHIFT button, then press the CHASE REV button and release the SHIFT button.
The rank is important !!
When a button has several meanings then they will be separated by a / sign. The text above the button will
be mentioned first, then the / sign and then the text below the button.
For example: <RECORD/SHIFT>
All indicators (lamps, display) are presented as [XXX]
For example [LAMPJE FADER 1]
All faders are presented as {FADER}
CMX24 JB SYSTEMS 2/93
®
OPERATION MANUAL
CMX24