neato Botvac Connected D3 Benutzerhandbuch Seite 3

reaCh
Neato Robotics' products are "articles" as defined in REACH
Article 3(3) and do not release substances under their
normal use.
The Technical Construction File is maintained at Neato
Robotics UK office.
The Authorized representative located within the community
is: Neato Robotics, UK Office. The last two digits of the year
the CE Mark was first affixed to Botvac models are 14.
fCC anD inDuStry CanaDa ComPlianCe Statment
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) T his device must accept any interference received,
including interference that may cause undesired
operation.
Caution: Changes or modifications not expressly approved
by Neato Robotics could void the user's authority to operate
the equipment.
RF Radiation Hazard Warning
To ensure compliance with FCC and Industry Canada RF
exposure requirements, this device must be installed in
a location where the antennas of the device will have a
minimum distance of at least 20 cm from all persons. Using
higher gain antennas and types of antennas not certified for
use with this product is not allowed. The device shall not be
co-located with another transmitter.
Maximum Antenna Gain
Currently, the maximum antenna gain for external antennas
is limited to -2.5 dBi (Botvac Connected)/-2.7 dBi (Botvac
D3/D5 Connected) for operation in the 2400MHz to
2483.5 MHz bands. The antenna gains must not exceed
maximum EIRP limits set by the FCC/Industry Canada.
Alternative
This radio transmitter (identify by certification number or
model number) has been approved by Industry Canada
to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance
for each antenna type indicated. Antenna types not included
in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with
this device.
Industry Canada Notice and Marking
The term "IC:" before the radio certification number only
signifies that Industry Canada technical specifications were
met.
Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and maximum
(or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other
users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is
not more than that necessary for successful communication.
This device complies with Industry Canada's license-exempt
RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This
device must accept any interference, including interference
that may cause undesired operation of the device.
CLASS 1 LASER PRODUCT
laSer: The Navigation Sensor contains a Class 1 rotating
laser per EN 60825-1 during all procedures of operation.
• Do not aim the laser at other persons.
• Do not look at the direct or reflected beam.
• Always switch the robot vacuum off during changeover
tasks.
• Modifications (changes) or attempts to repair the robot
vacuum cleaner or the navigation sensor are strictly
prohibited and may result in hazardous radiation exposure.
Laser Parameters.
• W avelength 785 nm
• P ulse Rep Frequency 1.8 kHz
• P ulse Duration 200 usec
• P eak Power 2.1 mW
• B eam Diameter 2.3 mm
• B eam Divergence -1.5 mrad
• C aution – Use of controls or adjustments or performance
of procedures other than those specified herein may
result in hazardous radiation exposure" (or alternatively,
equivalent appropriate warnings).
• I EC/EN 60825-1: 2014
end user license agreement, trademarks and Copyright
The Neato Robotics, Inc. End User License Agreement is
available online at NeatoRobotics.com. Neato Robotics ,
®
Botvac are registered trademarks of Neato Robotics Inc.
®
Other trademarks, trade names and service marks are the
registered and unregistered trademarks, trade names and
service marks of their respective owners.
QNX Software: Neato Botvac Series robots incorporate QNX
Software. © 1982-2008, QNX Software Systems. All rights
reserved.
Disposal.
Disposal of the Product
This symbol on product indicates the product must not
be disposed of with other household refuse. It must be
disposed of and collected for recycling and recovery of
waste EEE. For more information about where you should
dispose of your waste equipment for recycling and recovery
please contact your dealer or distributor from which your
product was purchased.
Disposal of batteries.
This symbol on the battery indicates the battery must
not be disposed of with other household refuse. It must
be disposed of and collected for recycling and recovery
through your local free battery collection system. For more
information about where you should dispose of your battery
for recycling and recovery please contact your dealer or
distributor from which your product was purchased.
REMOVE THE BATTERY FROM THE PRODUCT BEFORE
DISPOSAL AND DISPOSE SEPERATELY IN ACCORDANCE
WITH LOCAL REGULATIONS.
technical Data.
input voltage: 100-240V AC 50/60Hz 45W 0.4-0.8A
output voltage: Max 18V DC 36W 2.0A
Short Circuit and Over Current protection
battery: Li-Ion Rechargeable 4200 mAh or 2100 mAh
nominal Voltage: 14.4V
runtime: dependent on environment to be cleaned.
limited manufacturer's Warranty Summary
Neato Robotics, Inc. warrants to the original purchaser
("you" or "your") that your Neato hardware product
("Product"), excluding batteries and other consumables,
shall be free from defects in material and workmanship
for 1 year from the original date of purchase. In the case of
batteries, a Warranty Period of six (6) months shall apply
and 'Warranty Period' shall be read accordingly throughout
this document. In the case that the product purchased is a
Neato-Certified Refurbished product, a Warranty Period of
three (3) months shall apply and 'Warranty Period' shall be
read accordingly throughout this document. In the absence
of proof of purchase, Neato Robotics will take the date of
manufacture plus 90 days to allow for transit and sale as the
date of purchase.
This warranty is void if parts other than Neato Genuine
replacement parts are used including but not limited to
batteries, filters, brushes and boundary markers. Using
unauthorized, apparently compatible items available on
the market may damage your product or create an unsafe
situation.
You may also find the full details of this limited warranty
by selecting your Product in the Support section of our
website at NeatoRobotics.com. Except where prohibited by
applicable law, this warranty is nontransferable and is limited
to the original purchaser and applies only to products
purchased and used in the same country. This warranty gives
you specific legal rights, and you may also have other rights
that vary under local laws. If you are dealing as a consumer
this limited warranty does not affect your statutory rights.
Support.
Visit NeatoRobotics.com for the detailed Manufacturer's
Limited Warranty and for details on how to obtain support,
purchase replacement consumables.
May 1, 2016