Specifications; Additional Safety Rules - Makita HR2410 Betriebsanleitung

ENGLISH
1 Tighten
2 Loosen
3 Side grip
4 Bit shank
5 Bit grease
6 Bit
7 Chuck cover
8 Clamp screw

SPECIFICATIONS

Model
Capacities
Concrete ................................................................................... 24 mm
Wood ........................................................................................ 32 mm
Steel ......................................................................................... 13 mm
-1
No load speed (min ) .................................................................. 0 – 1,050
Blows per minute ......................................................................... 0 – 4,900
Overall length .............................................................................. 371 mm
Net weight .................................................................................... 2.4 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for hammer drilling and drilling in
brick, concrete and stone. It is also suitable for drilling
without impact in wood, metal, ceramic and plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear protec-
tors and thickly padded gloves.
2. Be sure the bit is secured in place before opera-
tion.
3. Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
4. In cold weather or when the tool has not been
used for a long time, let the tool warm up for sev-
eral minutes by operating it under no load. This
will loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
5. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
6. Hold the tool firmly with both hands.
7. Keep hands away from moving parts.
Explanation of general view
9 Depth gauge
10 Switch trigger
11 Reversing switch lever
12 Action mode changing knob
13 Blow-out bulb
14 Dust cup
15 Chuck adapter
16 Keyless drill chuck
8.
9.
10. When drilling or chipping into walls, floors or
11. Do not touch the bit or parts close to the bit
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Side grip (auxiliary handle) (Fig. 1)
The side grip swings around to either side, allowing easy
handling of the tool in any position. Loosen the side grip
by turning it counterclockwise, swing it to the desired
position and then tighten it by turning clockwise.
Installing or removing drill bit
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Clean the bit shank and apply bit grease before installing
the bit. (Fig. 2)
Insert the bit into the tool. Turn the bit and push it in until
it engages. (Fig. 3)
If the bit cannot be pushed in, remove the bit. Pull the
chuck cover down a couple of times. Then insert the bit
again. Turn the bit and push it in until it engages. (Fig. 4)
After installing, always make sure that the bit is securely
held in place by trying to pull it out.
To remove the bit, pull the chuck cover down all the way
and pull the bit out.
17 Sleeve
18 Ring
19 Tighten
20 Loosen
21 Wrench
22 Soft jaws
23 Screw
HR2410/HR2410X
Do not leave the tool running. Operate the tool
only when hand-held.
Do not point the tool at any one in the area when
operating. The bit could fly out and injure some-
one seriously.
wherever "live" electrical wires may be encoun-
tered, DO NOT TOUCH ANY METAL PARTS OF
THE TOOL!
Hold the tool by the insulated grasping surfaces
to prevent electric shock if you drill or chip into a
"live" wire.
immediately after operation; they may be
extremely hot and could burn your skin.
HR2413
24 mm
32 mm
13 mm
0 – 1,050
0 – 4,900
371 mm
2.3 kg
5